lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
 
Thread Tools Display Modes
Old 01-23-2014, 12:27 PM   #1
MyCousinVinnie
Gone Wild
Club Car
 
Join Date: Nov 2012
Posts: 328
Default Need help with motor test

I am still in the process of converting my 1993 club car 36v from resistor to solid state with 48v. Have potentiometer in, and its ohms are reading from 0 at rest to 5.23 when pedal pressed down. FSIP 700 amp controller. New heavy duty solenoid, which clicks. My problem is the cart still won't go.

I have disconnected the battery negative and positive and disconnected everything from motor.

I tested the continuity of the motor with the ohm meter set to 200. Here is what I got:

A1-A2 - continuity reads .9
S1-S2 - reads .5
nothing between any of a terminals and s terminals, as it should be.

I was about to battery test the motor with a twelve volt battery. I have seen the diagram, which requires a jumper between A2 and S1. See

http://www.buggiesgonewild.com/elect...otor-test.html
I have connected one of my short battery cables between these. But, the diagram then says to run cables to the battery and add make a "break." What is that exactly?

At my controller, I get full battery output at B+ and B- of 50.1 volts. At pin one on the controller, I get 50.1 volts. the solenoid clicks. At B- and M, I get 50.1 volts, but it does not drop when pedal is fully depressed as it should.

All connections triple, quadruple, etc. checked.

Any help is appreciated. Thanks.
MyCousinVinnie is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 01-23-2014, 12:43 PM   #2
scottyb
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 69,675
Default Re: Need help with motor test

make sure your pot and controller are operating on the same scale. 0-5k or 5k-0 Ωs . Check your pot out put.
scottyb is online now   Reply With Quote
Old 01-23-2014, 12:55 PM   #3
MyCousinVinnie
Gone Wild
Club Car
 
Join Date: Nov 2012
Posts: 328
Default Re: Need help with motor test

I checked it disconnected from controller. It goes from 0 to 5.23. How do I check whether controller is set to same?
MyCousinVinnie is offline   Reply With Quote
Old 01-23-2014, 04:07 PM   #4
sunoco
STEALTH 4X4
 
sunoco's Avatar
Club Car
 
Join Date: Sep 2011
Location: GA
Posts: 2,123
Default Re: Need help with motor test

Where did you get the controller?

What is the full serial number of the controller?
sunoco is offline   Reply With Quote
Old 01-23-2014, 06:53 PM   #5
MyCousinVinnie
Gone Wild
Club Car
 
Join Date: Nov 2012
Posts: 328
Default Re: Need help with motor test

Will look. Not in front of it now.
MyCousinVinnie is offline   Reply With Quote
Old 01-30-2014, 01:54 PM   #6
MyCousinVinnie
Gone Wild
Club Car
 
Join Date: Nov 2012
Posts: 328
Default Re: Need help with motor test

Full serial number is

Sscs-m38807-11

I still need help with motor test if anyone can give me some direction

I have a battery cable connected between s2 and a2

Now I need to know who to run from a1 and s1 to battery and what I need to do to make a "broken" connection.

Thanks.
MyCousinVinnie is offline   Reply With Quote
Old 01-30-2014, 02:03 PM   #7
sunoco
STEALTH 4X4
 
sunoco's Avatar
Club Car
 
Join Date: Sep 2011
Location: GA
Posts: 2,123
Default Re: Need help with motor test

Sorry what is the part number, not the serial number. Should start with 51- (example is 51-42L700NH0S)

Jumper S1 & A2

S2 to 12v positive
A1 to 12v negative

Only do this to make sure the motor turns. You will damage it if you let it run
sunoco is offline   Reply With Quote
Old 01-30-2014, 02:16 PM   #8
scottyb
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 69,675
Default Re: Need help with motor test

0-5k controller should have a model # that ends on NN0S
scottyb is online now   Reply With Quote
Old 01-30-2014, 03:08 PM   #9
sunoco
STEALTH 4X4
 
sunoco's Avatar
Club Car
 
Join Date: Sep 2011
Location: GA
Posts: 2,123
Default Re: Need help with motor test

Yeah I guess I could have used a correct example at least
sunoco is offline   Reply With Quote
Old 01-30-2014, 04:12 PM   #10
MyCousinVinnie
Gone Wild
Club Car
 
Join Date: Nov 2012
Posts: 328
Default Re: Need help with motor test

Model is fs42L 700nn0s
MyCousinVinnie is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
Motor Test Electric Club Car
L.v. Motor test Electric Club Car
GE 36V motor test Electric golf carts
Test motor Test Post
How to test a 48V motor??? Electric Club Car


All times are GMT -5. The time now is 11:01 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.