lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles



Post New Thread  Reply
 
Thread Tools Display Modes
Old 12-06-2011, 10:14 PM   #1
Rob52
Not Yet Wild
E-Z-GO
 
Join Date: Jan 2011
Location: Clio, MI
Posts: 13
Default bore out on G16

Anyone know if there is a ring and piston set for .10 over? JN-6 301 motor!!
My dads yami!! Overheated and warped.
Rob52 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 12-07-2011, 01:22 PM   #2
TheNewGuy
Admin/Moderator
 
TheNewGuy's Avatar
Yamaha
 
Join Date: Dec 2006
Location: Ohio
Posts: 16,112
Default Re: bore out on G16

I don't think you will find .100 O/S. I believe .050 O/S is max. But, I could be wrong.

TheNewGuy is offline   Reply With Quote
Old 12-07-2011, 04:16 PM   #3
Rob52
Not Yet Wild
E-Z-GO
 
Join Date: Jan 2011
Location: Clio, MI
Posts: 13
Default Re: bore out on G16

Sorry guys my typo.......... .010(ten thousanths) OB we measured it at about .007 out of round
looking to take off minimal material if possible

Last edited by Rob52; 12-07-2011 at 04:20 PM.. Reason: add info
Rob52 is offline   Reply With Quote
Old 12-07-2011, 06:54 PM   #4
smallblock450sl
Sometime's............
 
smallblock450sl's Avatar
Yamaha
 
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,442
Default Re: bore out on G16

G16's only have to oversided pistons available, .25 and .50 over. Standard bore 74.96mm-74.98mm, oversized 1-75.25mm and oversized 2-75.50mm. Rons right
smallblock450sl is offline   Reply With Quote
Old 12-07-2011, 08:17 PM   #5
Rob52
Not Yet Wild
E-Z-GO
 
Join Date: Jan 2011
Location: Clio, MI
Posts: 13
Default Re: bore out on G16

My dimwitted fault......didn't realize until I saw it closer it was mm and not standards....
.25mm is at .0098 thousanths, I'm good to go!
Will boring out and installing larger piston & rings change much with carb mix?
Is there a posting and /or shop manual recommended for the reassembly of the 301 motor?
Rob52 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha


Thread Tools
Display Modes


Similar Threads
Thread Forum
bore clearances Gas Yamaha
carb bore on g22 Gas Yamaha
341 bore questions?? Gas Club Car
89 clutch bore Gas EZGO
G1 bore Gas Yamaha


All times are GMT -5. The time now is 09:27 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.