08-04-2019, 10:59 AM | #1 |
Not Yet Wild
Join Date: Jun 2019
Posts: 61
|
EZGO Predator Swap- kill switch?
I'm getting close to firing up my cart and working in the last few details. I finished my exhaust(at least version 1.0)The predator has a grounded kill switch, but the cart has a 12v switch on accelerator pedal. I see two options. 1, add a second switch at the accelerator or 2, turn the idle down so low it won't idle when I'm off the gas pedal. I'm assuming the latter is the way to go. Please advise, thanks.
Sent from my SM-G930V using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-04-2019, 12:24 PM | #2 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: EZGO Predator Swap- kill switch?
Or option 3 just add a separate kill switch. My VC 460 cart I use the low idle cut off and the 440 snowmobile engine uses an ignition switch. BUT both have an emergency kill switch in case all else fails.
|
08-04-2019, 07:04 PM | #3 |
Not Yet Wild
Join Date: Jun 2019
Posts: 61
|
Re: EZGO Predator Swap- kill switch?
There's a kill on the engine I can reroute to below the driver. Option 4 is add a relay controlled by the gas pedal switch that grounds out when de-energized. Aka, it opens the ground(kill) circuit when you're on the gas, then closes the kill circuit when you're not. Would use the existing switch.
Sent from my SM-G930V using Tapatalk |
08-04-2019, 07:21 PM | #4 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: EZGO Predator Swap- kill switch?
I started with the bosch 5 pin relay as shown in the sticky with both carts. Later decided to simplify the systems to minimize potential electrical problems.
|
08-04-2019, 07:52 PM | #5 |
Not Yet Wild
Join Date: Jun 2019
Posts: 61
|
Re: EZGO Predator Swap- kill switch?
I'm thinking if I have the idle screw low enough, it will stall when I let off the gas anyway. Just got it started today. Seems to be running lean, I need to order some jets to dial it in. Looks like I can get an assortment from this place.
https://www.ombwarehouse.com/mega-jet-kit.html Sent from my SM-G930V using Tapatalk |
08-04-2019, 08:16 PM | #6 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: EZGO Predator Swap- kill switch?
A far better solution is to use the adjustable main jet. I used NR racing unit but at times there are others vendors selling for less.On page #1 of my $650 VC 460 thread Aaron from VC shares a link for the EC carbs unit.One note there is since the kit is designed for the smaller clone don't switch the emulsion tube.
|
08-04-2019, 08:35 PM | #7 |
Not Yet Wild
Join Date: Jun 2019
Posts: 61
|
Re: EZGO Predator Swap- kill switch?
You read my mind. I was just logging in to ask about an adjustable main jet. Thanks!!
Sent from my SM-G930V using Tapatalk |
08-04-2019, 08:46 PM | #8 |
Not Yet Wild
Join Date: Jun 2019
Posts: 61
|
Re: EZGO Predator Swap- kill switch?
That listing is a bit confusing... the title says for GX390 but the description says GX200. Is it designed to cover a range wide enough for both. Mine's a 301, right in between.
Sent from my SM-G930V using Tapatalk |
08-04-2019, 09:05 PM | #9 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: EZGO Predator Swap- kill switch?
That what I was trying to say. The listings are confusing but the same main jet fits all of them but not the emulsion tube is too small for the bigger engines fortunately the stock emulsion tube works fine.
|
08-04-2019, 10:35 PM | #10 |
Not Yet Wild
Join Date: Jun 2019
Posts: 61
|
Re: EZGO Predator Swap- kill switch?
I was looking at the VC 3 circuit carb, but that's listed for the 420/460's. I contacted VC, they don't make a smaller one. Is there a better carb than the stock one for my 301 or should I just use the adjustable jet and dial it in as best I can.
Sent from my SM-G930V using Tapatalk |
|
|
Similar Threads | ||||
Thread | Forum | |||
Finally started my EZGO Predator Swap | Clone Engine Swaps | |||
Which secondary Clutch for EZGO with 670cc Predator swap | Clone Engine Swaps | |||
Ezgo predator swap issues | Clone Engine Swaps | |||
88 CC DS Clone swap: the kill wire | Clone Engine Swaps | |||
Key switch & Kill switch question | Gas Club Car |