|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
04-24-2019, 08:04 PM | #1 |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Installing Alltrax 300A Controller
Getting ready to install a new Alltrax 300A controller in a 2012 Precedent Excell cart and have a couple of questions.
I already have a resister on my solenoid, do I need to install the one that came with the kit? The 4 pin connector that came off of the old controller, I don't see a socket where it connects to the new controller, is it needed? Are you mounting the new controller to the existing aluminum plate the old controller was bolted to, or the plastic wall on the back side of the compartment the old controller and solenoid hides in? Thanks in advanced, I.m sure ill have more questions. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-24-2019, 09:20 PM | #2 | |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: Installing Alltrax 300A Controller
Quote:
|
|
04-24-2019, 09:42 PM | #3 |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Re: Installing Alltrax 300A Controller
Im using the stock solenoid and there are only two post on it plus two spade connectors. The directions and other post say to connect the diode to the small post on the solinod which I don't have. Do I connect the diode only two hmm post on the solenoid?
Sent from my SM-G950U using Tapatalk |
04-24-2019, 10:17 PM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,356
|
Re: Installing Alltrax 300A Controller
Install no precharge resistor with the Alltrax XCT. That's the green thing between the big posts in your pictures. Do not reinstall it.
The small post diode is built into the stock solenoid as indicated by the red mark on the + small post. So you need not add that either. Hope this helps |
04-25-2019, 12:19 AM | #5 | |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: Installing Alltrax 300A Controller
Quote:
Here it is on the Alltrax drawing attached. Note: #5 is the Regen Diode and #4 was the Resistor which is noted as no longer needed (as it is handled through the controller now). If you have a polarized solenoid (which sounds like you do) the Note for #1 is not applicable as it is built in on your solenoid and you would not have had one to begin with. |
|
04-25-2019, 06:01 AM | #6 | |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Re: Installing Alltrax 300A Controller
Quote:
Sent from my SM-G950U using Tapatalk |
|
04-25-2019, 07:12 AM | #7 |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: Installing Alltrax 300A Controller
10-4. If I miss u I will be in some meetings, leave me a message and I will call u inbetween.
|
04-25-2019, 08:06 AM | #8 |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Re: Installing Alltrax 300A Controller
|
04-25-2019, 08:27 AM | #9 |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Re: Installing Alltrax 300A Controller
|
04-25-2019, 08:30 AM | #10 |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Re: Installing Alltrax 300A Controller
20190424_203701.jpgOne last picture of my stock solenoid, and of course its upside down and I'm unable to rotate it.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Installed Alltrax XCT 300a controller, new solenoid. nothing works | Electric Yamaha | |||
Installing Alltrax XCT speed controller | Electric EZGO | |||
Installing Alltrax controller | Electric Club Car | |||
Alltrax controller npx 4834 48v 300a?? | Electric Club Car | |||
Installing an Alltrax controller in 30 sec (video) | Extreme DC! |