FSIP speed motor upgrade question

[mgray70]

Just wondering if anyone could tell me what I could expect with the FSIP MOT-A3 speed motor. The cart is a club car precedent IQ with 22" tires and stock controller for now. The cart is currently at 19-20 mph. Looking for at least 25-28 mph. Anyone running anything similar?

Sent from my SM-G930R4 using Tapatalk

[Aflyer]

mgray70,
Check my signature, for the 2013 Precedent upgrades I did. This package came from David at Revolution Golf Cars, a site sponsor.

I get 27 mph all the time, with an occasional 28, 29 with a tail wind. I do need to work with Alltrax, because I am not sure that I have it tuned the best that I can.

27 mph is pretty quick, especially with only rear wheel brakes.

Aflyer

[scottyb]

With any of the Alltrax XCT controllers, 27 mph on stock tires.
The stock controller will limit the motor to stock speed.

[net]

Fsip exelente . Good company
Where did you buy it?

Enviado desde mi SGH-I337M mediante Tapatalk

[mgray70]

Originally Posted by scottyb

With any of the Alltrax XCT controllers, 27 mph on stock tires.
The stock controller will limit the motor to stock speed.

So what you're saying is with the stock controller I probably won't see any difference? What about the XCT400 with the stock motor? What kinda speed increase would that give. Looking for the best option without having to change both speed control and motor at the same time. Looking around 25 mph or so.

Sent from my SM-G930R4 using Tapatalk

[PingEye3]

As per ScottyB above; replace controller first. You will get the performance you want. XCT48400
http://www.cartsunlimited.net/alltrax-xct-sepex--.html

[Gregorio]

With the XCT400 and stock motor I can hit 25. Buy the XCT500 for $15 more, however.

[scottyb]

Originally Posted by Gregorio

With the XCT400 and stock motor I can hit 25. Buy the XCT500 for $15 more, however.

Gawd, I have to hike my pricing!?


If you read the forum you have already read
the XCT control sets the RPM limit to 6000 rpms by default which allows the average speed of 22-23 mph in CC and Ezgo with Yamaha being a little slower 20-21 mph. The top speed with any aftermarket motor will be limited by the stock controller..... as well as the torque due to the 225a max flow from the stock controller.

I suggest you do the controller upgrade - then later go for the motor you want.

[mgray70]

Originally Posted by scottyb

Gawd, I have to hike my pricing!?


If you read the forum you have already read
the XCT control sets the RPM limit to 6000 rpms by default which allows the average speed of 22-23 mph in CC and Ezgo with Yamaha being a little slower 20-21 mph. The top speed with any aftermarket motor will be limited by the stock controller..... as well as the torque due to the 225a max flow from the stock controller.

I suggest you do the controller upgrade - then later go for the motor you want. [emoji106]

Thanks Scotty! I was originally thinking controller first, but then reading a lot of good stuff about that motor, didn't know which way would be best first. You may be hearing from new soon!

Sent from my SM-G930R4 using Tapatalk

[scottyb]

On my 2014 Prec I upgraded in this progression:
1. dealer speed code 4 = 19.mph
2. FSIP A3 high speed motor = same 19 mph (controller limit)
3. XCT48300 (smallest controller yet 135 peak amps higher) = 27 mph