|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
05-08-2017, 11:18 AM | #1 |
Not Yet Wild
Join Date: Mar 2017
Posts: 35
|
Alltrax SR error flag, High Throttle Input Under-range
I have an Alltrax SR 48400, HD 200Amp Solenoid, and HD F/R switch setup (ScottyB - Thanks!) running a MOT-A1 on a 2000.5 DS. Non-MCOR
Everything is great however having a small issue with trying to creep the cart from a dead stop (easing in to parking spot, garage, etc) The controller throws the High Throttle Input Under-range flag and shuts down causing a jerk. To avoid guesswork in what part of the programming I need to adjust (if it's a programming issue), can anyone clue me in? I'll try to post my settings. Sent from my iPhone using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-08-2017, 11:28 AM | #2 |
Not Yet Wild
Join Date: Mar 2017
Posts: 35
|
Alltrax SR error flag, High Throttle Input Under-range
Ok. After further analysis, the jerk does not occur simultaneously with the error flag. So the title may be off a bit or unrelated. However, the jerking happens as I release the pedal to coast the cart into place or trying to ease into acceleration.
Could it be a slipping axle deal? What are the torque specs for the u-bolts? I have a Jake's 6" lift. Sent from my iPhone using Tapatalk |
05-08-2017, 12:37 PM | #3 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,417
|
Re: Alltrax SR error flag, High Throttle Input Under-range
Your pedal is maxing the speed signal out about 80% of it's travel yet you have the throttle rate down very low. I would make the last box in the throttle chart 100/100 and ditch those dots in the straight part of the red line, they are not needed.
Put it back to more of a bell curve like below. You can even copy these chart numbers as a start point. |
05-08-2017, 01:28 PM | #4 |
Not Yet Wild
Join Date: Mar 2017
Posts: 35
|
Re: Alltrax SR error flag, High Throttle Input Under-range
Thanks ScottyB! Do you have a screenshot of the Speed curve so I can see those numbers as a starting point? Do you have a recommended throttle rate beginning/end? Yeah, mine is set low thinking that was my issue.
Sent from my iPhone using Tapatalk |
05-08-2017, 02:05 PM | #5 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,417
|
Re: Alltrax SR error flag, High Throttle Input Under-range
On the throttle 12.5 is default for SR controls but I find that high and like 9-10.5 and then 1/2 of that in your FN1 adjustment band.
I attached a pic of the curve in the last post? I'll bet you are viewing the forum with your phone... |
05-08-2017, 02:07 PM | #6 | |
Not Yet Wild
Join Date: Mar 2017
Posts: 35
|
Re: Alltrax SR error flag, High Throttle Input Under-range
Quote:
Ok, I'll give that a shot. Yep, on my phone...good call. Sent from my iPhone using Tapatalk |
|
05-08-2017, 02:41 PM | #7 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Alltrax SR error flag, High Throttle Input Under-range
If You still have issues after adjusting the programming, You may have a hardware problem.
If the Multi-Step potentiometer is OFF post #3 before the pedal micro-switch opens, You will get an under-range error. You can fix that by putting a piece of wire between post #2 and #3. http://www.buggiesgonewild.com/attac..._resistors.jpg |
05-08-2017, 06:07 PM | #8 |
Not Yet Wild
Join Date: Mar 2017
Posts: 35
|
Re: Alltrax SR error flag, High Throttle Input Under-range
Thank you both! I did match ScottyB's speed/torque curves recipe and it certainly improved the overall acceleration, however, the bucking when trying to inch the cart forward/reverse remains. I got side-tracked with Dad duties so I'll have to do Sergio's mod and testing another time and let you know the results.
Sent from my iPhone using Tapatalk |
05-08-2017, 06:22 PM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,417
|
Re: Alltrax SR error flag, High Throttle Input Under-range
The bucking at low throttle signal is pretty unusual. Since the Alltrax auto calculates your signal it would seem like the signal is inconsistent in that low range.
|
05-08-2017, 06:39 PM | #10 | |
Not Yet Wild
Join Date: Mar 2017
Posts: 35
|
Re: Alltrax SR error flag, High Throttle Input Under-range
Quote:
We'll see if Sergio's analysis does the trick. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
XCT 500 errors- High Throttle Input Under | Electric EZGO | |||
600 amp alltrax error codes | Electric EZGO | |||
High-Speed Walk-away error message on IQ Cart | Electric Club Car | |||
Alltrax SPM "low throttle" error code | Electric EZGO | |||
Reducer 33-75v input range | Electric Club Car |