lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
 
Thread Tools Display Modes
Old 01-31-2020, 02:01 PM   #1
Jake_Daddy
Gone Wild
 
Jake_Daddy's Avatar
Club Car
 
Join Date: Nov 2018
Location: Florida
Posts: 370
Default Wiring Alltrax for reverse with single micro-switch F&R switch...

Should have a 500a Alltrax coming today or tomorrow to work a solid state conversion and as I am reviewing the wiring diagrams I am wondering how to wire up the reverse input out of a single micro-switch F&R. Looks like I need to add an additional switch up to achieve this. Has anyone else worked up a slick solution for this? Thanks
Jake_Daddy is offline   Reply With Quote
Old 02-01-2020, 10:37 AM   #2
NoleFan4Ever
MOD of all BS!
 
NoleFan4Ever's Avatar
Club Car
 
Join Date: Sep 2011
Location: Florida
Posts: 17,477
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

I think I remember Sergio doing or helping someone with this. I have never had to do it, but PM him and if it can be done, he will know how.
NoleFan4Ever is offline   Reply With Quote
Old 02-01-2020, 10:56 AM   #3
scottyb
Happy Carting
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

Look at the old diagrams showing a single ms and back up beeper. I think you will find something there.
scottyb is offline   Reply With Quote
Old 02-01-2020, 03:50 PM   #4
Jake_Daddy
Gone Wild
 
Jake_Daddy's Avatar
Club Car
 
Join Date: Nov 2018
Location: Florida
Posts: 370
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

David Hicks straightened me out. I was under the assumption that the pin on the controller had to get a signal but apparently that's only if you want 1/2 speed reverse. We will try it out with full speed reverse and if we want to adjust it I will look into it more. I was wondering about using the buzzer signal but I haven't checked to see what the voltage it gets is yet. After a quick look yesterday I didn't get a good feel for the buzzer wiring, one wire goes to the back of the charge socket and one wire goes to the solenoid so I am a bit confused how that gets triggered.
Jake_Daddy is offline   Reply With Quote
Old 02-02-2020, 11:06 AM   #5
Jake_Daddy
Gone Wild
 
Jake_Daddy's Avatar
Club Car
 
Join Date: Nov 2018
Location: Florida
Posts: 370
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

Ok back to another question for the FnR where I have more connections than what the wiring diagram shows. My FnR isn't labeled so the picture is what I assume is correct. Are two lower bars coming out jumpered together? The wiring diagram makes it look like those are the two you connect to but I would like to verify if I do that I leave the top bar open. I feel like something needs to be jumpered or left open here any input would be appreciated.
Attached Images
File Type: png F&R to Alltrax.PNG (28.3 KB, 0 views)
Jake_Daddy is offline   Reply With Quote
Old 02-02-2020, 11:38 AM   #6
Fairtax4me
Bonafide Nincompoop
 
Fairtax4me's Avatar
Club Car
 
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

I could be wrong but I’m thinking the bottom bars should be jumped together for a controller setup. So you’ll have A2 to bottom bars, M- to top bar.

The bottom bars were separate on the toaster coil carts to provide 18 or 24v for lower speed reverse. But thats not necessary with the alltrax controller.
Fairtax4me is offline   Reply With Quote
Old 02-02-2020, 11:46 AM   #7
Sergio
Gone Wild
 
Sergio's Avatar
Club Car
 
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

what he said
Sergio is offline   Reply With Quote
Old 02-02-2020, 12:49 PM   #8
Jake_Daddy
Gone Wild
 
Jake_Daddy's Avatar
Club Car
 
Join Date: Nov 2018
Location: Florida
Posts: 370
Default Re: Wiring Alltrax for reverse with single micro-switch F&R switch...

Thanks guys! I really appreciate it.
Jake_Daddy is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
Series F/R switch micro switch wiring? Electric EZGO
1982 club car forward reverse micro switch keeps shorting out Electric Club Car
Micro switch wiring help Electric EZGO
F/R--micro switch wiring? Electric EZGO
Wiring for Micro switch in 1989 V-glide Electric Club Car


All times are GMT -5. The time now is 05:32 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.