12-03-2020, 12:16 PM | #1 |
Gone Wild
Join Date: Oct 2012
Location: SoCal
Posts: 671
|
How to make your own ICON programming cable
By request, here's a quick video I made on how to make your own ICON programming cable. You still need the proprietary ICON software, which isn't public so you'll have to ask your dealer or ICON for it (not me, sorry).
It was freezing in my garage and I was rushing to make the video short because I hate watching 20+ min videos to get a small amount of information, so for criticism keep that in mind https://www.youtube.com/watch?v=9obqQ2zn67s Parts List
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-12-2020, 09:28 PM | #2 |
Not Yet Wild
Join Date: Apr 2019
Posts: 24
|
Re: How to make your own ICON programming cable
Love this. Thanks for posting. Plan on emailing icon and asking for a copy. Worst case I get a “no” no one in a few hours from here in GA that I’ve found willing to do it for me.
|
12-14-2020, 11:06 AM | #3 | |
Gone Wild
Join Date: Oct 2012
Location: SoCal
Posts: 671
|
Re: How to make your own ICON programming cable
Quote:
I'm sure it'll get posted on here eventually. |
|
01-24-2021, 12:29 PM | #4 |
Not Yet Wild
Join Date: Jan 2021
Posts: 5
|
Re: How to make your own ICON programming cable
Anyone have any luck getting a copy of the NEOS software?
Thanks |
02-22-2021, 10:22 AM | #5 |
Getting Wild
Join Date: Jan 2019
Location: South Florida
Posts: 123
|
Re: How to make your own ICON programming cable
Atrain
Thanks for the knowledge. Was able to attain the software and just ordered what I needed. Gunna be a pricy little cable. Would love to pick your brain. I shot you a DM a while back, if you can reach out Id love to connect. |
06-14-2021, 05:46 PM | #6 |
Not Yet Wild
Join Date: Jun 2021
Posts: 1
|
Re: How to make your own ICON programming cable
Could I buy one off you?
|
06-14-2021, 07:23 PM | #7 |
Gone Wild
Join Date: Oct 2012
Location: SoCal
Posts: 671
|
Re: How to make your own ICON programming cable
They're on Amazon now - https://www.amazon.com/dp/B09253SPKC
|
06-19-2021, 08:44 AM | #8 |
Not Yet Wild
Join Date: May 2018
Posts: 57
|
Re: How to make your own ICON programming cable
Just came across this, you’ve commented on my other posts about increasing torque in my icon i60L. Curious, instead of getting a 600a controller (which is probably overkill to be honest), if I can get the software which I downloaded already just need to try and install it still, can I just adjust the torque with the software in the stock 350a controller and get more out of it, or is it pretty much maxed out for the amperage it has? Would obviously be much cheaper to adjust the existing controller and purchase a cable from you on Amazon if that will work. Not sure if anyone’s done or tried it and how successful and about how much difference it made with a 350 amp controller. Thanks for any info/feedback!
|
06-20-2021, 07:37 PM | #9 |
Getting Wild
Join Date: Nov 2020
Posts: 76
|
Re: How to make your own ICON programming cable
Atrain, just loaded the software and ordered the RS232 to Molex from Amazon. The last part is the CAN:CANUSB from CANUSBshop by Imagecraft correct? There is no "CAN open API" software needed to program the cart, right?
Please reply |
06-21-2021, 12:34 PM | #10 | |
Gone Wild
Join Date: Oct 2012
Location: SoCal
Posts: 671
|
Re: How to make your own ICON programming cable
Quote:
|
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Icon programming/speed limit? | Icon | |||
Programming cable connector / adaptor | Electric EZGO | |||
Cable adapter for CC and Curtis programmer. Can I make one? | Electric Club Car | |||
What cable needed for Alltrax DCX programming | Electric Club Car | |||
Can you use jumper cable to make wires | Electric EZGO |