2022 Evolution Programming Tool

[evoster]

Originally Posted by KC-EV

Exactly what I was needing. Thank you!!

If you haven't already, look at the FJP project file that I posted here. You can use it with the programming software without connecting to your cart and then dig thru all the other tabs and parameters offline.

[nokocart]

Really great info all. Thanks!

Programming question. I would like to set my low setting top speed to match my speed limit in my neighborhood so i can just pedal to the floor and the old ladies wont report me to the HOA police. Is there a way to tune in the low speed RPM?

Thanks for any help.

[evoster]

Originally Posted by nokocart

Really great info all. Thanks!

Programming question. I would like to set my low setting top speed to match my speed limit in my neighborhood so i can just pedal to the floor and the old ladies wont report me to the HOA police. Is there a way to tune in the low speed RPM?

Thanks for any help.

Look at the Slow Mode tab. Picture attached

[nokocart]

Well I feel dumb. I didn't even see that tab. Thanks for the help the cart is happy with the new settings!

[Silvr_Scream]

Originally Posted by evoster

Look at the Slow Mode tab. Picture attached

Any experience with the electronic brake adjustment to make it not so harsh when braking?

[evoster]

Originally Posted by Silvr_Scream

Any experience with the electronic brake adjustment to make it not so harsh when braking?

It varies with controller type and associated software.
For the EV48-400 and EV48-400-A :

Turn on/off Electromagnetic brake (motor brake) function on these tabs:
- Calibration>Electromagnetic brake
- Calibration>Slop control

Turn on the Electromagnetic brake (motor brake):
- Set “Electromagnetic brake control type” to “Driver4”
- Set “Slop control mode” to “Stop in slop”
- Adjust “Electromagnetic brake release speed”
- Adjust “Electromagnetic brake release delay time”

Turn off the Electromagnetic brake (motor brake):
- Set “Electromagnetic brake control type” to “Disable”
- Set “Slop control mode” to “Slide in slop”

Besides EM settings, there's also the deacceleration settings in Zonal tab for when foot is off pedal

Calibration > Zonal gear mode >

1 partition deceleration of P mode (rpm/s)
2 partition deceleration of P mode (rpm/s)
3 partition deceleration of P mode (rpm/s)
4 partition deceleration of P mode (rpm/s)
5 partition deceleration of P mode (rpm/s)
6 partition deceleration of P mode (rpm/s)
7 partition deceleration of P mode (rpm/s)

- Setting higher “rpm/s” will provide stronger deceleration on Forward direction at
high speed mode (P mode) .
- Conversely setting smaller ““rpm/s” will provide softer deceleration

It`s recommended to adjust all the rpm range deceleration value synchronously otherwise the deceleration process may not be smooth, you may experience uncomfortable deceleration.

[1thirtyone]

I'm hoping that someone familiar with the 2022 and newer evolution carts can help me with a programming/connectivity issue. I have verified that I have both the correct cart cable and the correct program, but have been unable to connect. I went as far as to download the program from another source and also to another lap top, adjusted port settings etc. I keep coming up with the same error message. I am adding a screen shot prior to loading the file as well as one after trying to connect. Any advice would be greatly appreciated.

[evoster]

Originally Posted by 1thirtyone

I have verified that I have both the correct cart cable and the correct program, but have been unable to connect.

You have verified you have the correct cable. But since that cable works with the EV48-400 AND the EV48-400-C controllers, I have to ask which controller version do you have? Can you post a clear picture of your controller label?

[1thirtyone]

Thank you for the response. Please see attached pics, I have the EV48-400.

[evoster]

Originally Posted by 1thirtyone

I have the EV48-400.

Send me a PM and I'll help debug