|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-02-2015, 07:47 AM | #11 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
|
Re: axle bearing and seal replacement.
Okay coffee.
Remove the axle nut. Place the axle in the vice so the bearing surface is above the jaws. Tighten the vice. Put a light coat of light oil on the bearing surface. Place the new bearing on the axle, Place the old bearing on top of it. Slide the 3/4 pipe down on top of the axle and tap it with a small heavy hammer until the bearing reaches the seat area. Observe there is not stop for the bearing & it can be driven too far. If this happens use the removal method to back it off. When the bearing is properly placed remove the pipe and old bearing and slide the axle into the tube. If the new bearing resists insertion in the tube put the axle nut on backwards to protect the threads and tap the axle until the bearing just passes and exposes the C lip groove. Install C clip. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-02-2015, 12:18 PM | #12 |
Gone Wild
Join Date: Apr 2013
Location: La Quinta
Posts: 273
|
Re: axle bearing and seal replacement.
another question. Is the standard EZGO replacement bearing kit 611931 the only option or is their a better bearing kit available? Just like in cars, are there good-better-best options?
|
10-02-2015, 02:35 PM | #13 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
|
Re: axle bearing and seal replacement.
I use 6004LL google it.
|
10-02-2015, 10:39 PM | #14 | |
Gone Wild
Join Date: Jul 2015
Location: Alpharetta, GA
Posts: 226
|
Re: axle bearing and seal replacement.
Quote:
|
|
11-04-2015, 08:20 AM | #15 |
Getting Wild
Join Date: Jun 2015
Location: Venice, FL
Posts: 128
|
Re: axle bearing and seal replacement.
Great information in this thread. Should be a sticky/reference up at the top of the page. I'm sure there will be more who want to do this job but don't have a press and/or slide hammer to work with.
Good stuff..... |
11-05-2015, 08:35 AM | #16 |
Getting Wild
Join Date: Jun 2015
Location: Venice, FL
Posts: 128
|
Re: axle bearing and seal replacement.
Just wanted to add. I ran into some trouble trying to get the oil seal out, and I don't have a puller. So, I carefully drilled two pilot holes, 180 degrees apart, on the face of the seal. I then inserted two screws, and pulled on the heads with vice grips. On the drivers side, this worked and the seal came right out.
On the passenger side, I had to also very carefully strike the ID of the seal with a flat head screw driver, again 180 degrees apart, to buckle the seal. It than came out no problem when I pulled on the screws. The key is to not mare the ID of the tube when doing all this. If you do, you need to smooth it out so there is no burr protruding. This can be done with a file, sandpaper, or a stone. |
06-01-2016, 06:51 AM | #17 |
Not Yet Wild
Join Date: Jun 2016
Posts: 2
|
Re: axle bearing and seal replacement.
i was hoping this had the info I needed, but it doesn't seem to...
what do you guys use to remove the bearing? a slide hammer with a hook type tool on the end? also whats required in removing the axle shaft itself?? |
06-01-2016, 08:07 AM | #18 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
|
Re: axle bearing and seal replacement.
mh0384
A small slide hammer with a hook removes the seal the best, there are other methods in the posts directly before your question. The axle will usually just slide out in the case where it is stuck I use a small slide hammer with an axle nut welded onto it so I can screw this onto the axle and pull. Welcome to BGW |
06-01-2016, 08:45 AM | #19 |
Not Yet Wild
Join Date: Jun 2016
Posts: 2
|
Re: axle bearing and seal replacement.
thanks scotty, I have a 1996 TXT, does that axle definitely slide out with no c-clip inside the diff?? I remember sliding it back and forth with my fingers but it stopped after an inch or so
I think what I meant to ask was... will a slide hammer with a hook be able to remove just the bearing? I see there are 2 snap rings, 1 on each side of the bearing... it just makes me wonder if there is enough to grab... |
03-10-2017, 07:36 PM | #20 |
Not Yet Wild
Join Date: Nov 2015
Posts: 32
|
Re: axle bearing and seal replacement.
Scottyb is dead on, as usual. I found this part today at my local NAPA parts store---exact replacement!
The key to the proper part is the four-digit number---6004---since you might find it with other than the LL identifier of Scotty's part. For example, the part I bought today ended in RS. No problem. Sid007 |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Yamaha G1 seal replacement files | Gas Yamaha | |||
Axle Bearing | Electric Club Car | |||
louder exhaust after seal replacement | Gas Yamaha | |||
Bearing replacement | Electric EZGO | |||
g1 crank seal replacement | Gas Yamaha |