lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas EZGO > Ezgo Gas Tech
Ezgo Gas Tech Resource info, wiring diagrams and how to's for Gas powered EZGO golf carts



 
 
Thread Tools Display Modes
Old 04-11-2008, 11:17 AM   #1
Timbeaux38
Derailng a thread somewhe
 
Timbeaux38's Avatar
E-Z-GO
 
Join Date: Mar 2008
Location: Alabama
Posts: 169
Default Pulling the body for paint

Is there a special way to yank the body off of an 03? Any time saving tips are appreciated. TIA

Tim
Timbeaux38 is offline  
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 04-11-2008, 02:58 PM   #2
Loud & Lifted
Here for the beer
 
Loud & Lifted's Avatar
E-Z-GO
 
Join Date: Mar 2008
Location: Damon Texas
Posts: 1,459
Default Re: Pulling the body for paint

ruredy told me to drill the rivets out but drill slowly because the heat from drilling will melt the plastic.
Loud & Lifted is offline  
Old 04-11-2008, 04:33 PM   #3
ruredy
Born Wild
 
ruredy's Avatar
 
Join Date: Mar 2007
Location: Clover SC.
Posts: 5,552
Default Re: Pulling the body for paint

There are a few bigger harden rivets you need to just use a chisel on. a drill bit might make it through one. Bob-O did a nice write up on how to remove these bodys, maybe he can post that here and we'll make it a sticky thread
ruredy is offline  
Old 04-11-2008, 05:33 PM   #4
Bob-0
Gone Wild
 
Bob-0's Avatar
 
Join Date: Feb 2007
Posts: 176
Default Re: Pulling the body for paint

Hi guys

I actually saved that thing I wrote... don't know why, but now I'm glad I did

Preparation:

To begin with removing the body, we need to make that possible by removing some things first:

Top - Remove each of the 4 bolts. The head is a Phillips head, and use a #2 Phillips screwdriver to hold them (preferably a short handle). Use a 7/16" socket to remove the lock nuts. Save the hardware by putting it all in a bag (Including the plastic spacers), and labeling it for the appropriate section.

Front Top Support - This is a one piece support, so its best to remove the lower two bolts first and rotate the entire piece so that it rests on the seat. Use a 1/2" socket w/ratchet to remove each of the 4 bolts. Again, save the hardware in a bag.

Rear Seat Back Support Frame - Instead of removing the rear top supports, we can save a few extra steps. At the base of the seat back supports, you will see 4 bolts. Use a 9/16" socket, and remove each one. They can be difficult to remove, and they are long bolts so be ready to put some grunt into them. An Air ratchet works very well, if you have access to one. Once those bolts are removed, you may now remove the framework, which includes seat back and all.
Reference Picture:


Rear Access Panel - You will see a black plastic cover in the middle of where the rear seat back support frame was. That panel has 5 screws holding it in place. Use a #20 torx bit to remove each screw. Don't forget to bag and label everything .
*** SAVE THIS 'J' CLIP***






FRONT COWL
-First things first, we must remove the rocker panels and sill plates.

Sill Plates - Start by removing the sill plates. These are the stainless steel covers just at the entryway to the golf car. There are two Phillips head bolts on each plate. Use a screwdriver and a 7/16" combination wrench to remove each one. You may need to soak them down with WD-40 for several hours first. If one breaks, you can get a replacement from your local dealer.
Reference Picture (My method )


Rocker Panels - There are two rivets on the rocker panels, drill those out with a 3/16" drill bit. Then gently, but firmly, pull the rocker panels free. They are held on by friction locks (once rivets are removed).
Reference Picture:


Front Cowl - With the rocker panels removed, we have now exposed the lower most rivets that hold each lower side of the cowl in place. First we need to start at the front and work our way back.

Name Plate - Right behind the name plate are two snap nuts on the mounting studs. You can use a small, flat blade screwdriver to remove these. If they prove to be troublesome, you can use a pair of dikes to remove ONLY the snap nut. The name plate can now be removed, thereby exposing the two rivets beneath it. Drill those two rivets out with the same 3/16" drill bit.
Reference Picture:


Lower Cowl Rivets - The rivets that were revealed earlier by removing the rocker panels may now be drilled out. I prefer to use a small pickle fork to get behind the body and remove the rivet. If you plan on reselling or using the cowl, you can drill out the head of the rivet and use a 3/8" punch to remove the body of the rivet.

Upper Cowl Rivets - Now, we can finish removing the cowl. Along the seating side of the cowl, you will see many rivets. Drill out each one, alternating sides. This way when you get to the last one in the middle, you can hold the cowl to prevent it from falling to the ground.


REAR BODY

Now the fun begins . This is the section that will take the longest to remove.

Seat Hinge Plates - After removing the seat from the car, you will notice the hinge plates that hold the seat on the car. Each one has two rivets that need to be drilled out with the same bit from earlier. There is also one rivet between each plate, right above the shift handle. Drill that out also.

Floorboard Rivets - Pull up the floor mat, starting at the rear body and pull to front of car. You will now see 5-6 rivets holding the lower ledge to the frame. Drill each of those out, same 3/16" drill bit. These rivets like to spin, if they do that then drill the heads off. Then use a 1/4" punch to remove the bodies after removing the rear body.

Side Rivets - Just in front of the rear wheel wells, you will see two 1/4" stainless steel rivets on each side. These were hidden by the rocker panels. Trying to drill these out is hopeless. The best method for removing them is to use a chisel and hammer. Remove the head of these, and use a punch to remove the rivets' bodies. Remove all 4 of these lower rivets this way.


Rear Bag well - There are two drive rivets to be punched out. These are located in each corner of the rear section of the bag well. Use a 1/4" punch to remove the pin. Then pull the rivet up by hand, and save the pin for reuse.
Reference Pictures:




You can now remove the entire rear body.

Now, finally she's naked

Have fun with your project(s), and I hope this has helped you out.

Bob
Bob-0 is offline  
Old 04-11-2008, 07:29 PM   #5
ruredy
Born Wild
 
ruredy's Avatar
 
Join Date: Mar 2007
Location: Clover SC.
Posts: 5,552
Default Re: Pulling the body for paint

Great post Bob, Thanks for sharing!!!!
ruredy is offline  
Old 04-11-2008, 07:44 PM   #6
spriddle
Admin
 
spriddle's Avatar
Yamaha
 
Join Date: Dec 2006
Location: TN
Posts: 101,826
Default Re: Pulling the body for paint

Quote:
Originally Posted by ruredy View Post
There are a few bigger harden rivets you need to just use a chisel on. a drill bit might make it through one. Bob-O did a nice write up on how to remove these bodys, maybe he can post that here and we'll make it a sticky thread
I love all the rivets in an Ezgo.

spriddle is offline  
Old 04-11-2008, 07:45 PM   #7
spriddle
Admin
 
spriddle's Avatar
Yamaha
 
Join Date: Dec 2006
Location: TN
Posts: 101,826
Default Re: Pulling the body for paint

Nice post Bob-O.

spriddle is offline  
Old 04-11-2008, 07:52 PM   #8
Timbeaux38
Derailng a thread somewhe
 
Timbeaux38's Avatar
E-Z-GO
 
Join Date: Mar 2008
Location: Alabama
Posts: 169
Default Re: Pulling the body for paint

Awesome post Bob!!!!!

Thanks !!!!
Timbeaux38 is offline  
Old 04-11-2008, 08:53 PM   #9
Bob-0
Gone Wild
 
Bob-0's Avatar
 
Join Date: Feb 2007
Posts: 176
Default Re: Pulling the body for paint

Thank you , I always enjoy getting to help with stuff like that. Call me strange, but taking 10 or 20 mins to make a post is a nice study break for me. I'm getting ready for my interview with Mesaba Airlines in just about 2 weeks now. So getting back to what I grew up around really helps to calm my nerves.... for a minute

Spriddle, the funny thing is now the RXV has no rivets in it at all. Its all torx screws and lock nuts . The reason (I just learned ) is because the manufacturer of Torx screws is Cargill, a Division of Textron

Have a great one
Bob
Bob-0 is offline  
Old 04-12-2008, 07:30 PM   #10
Timbeaux38
Derailng a thread somewhe
 
Timbeaux38's Avatar
E-Z-GO
 
Join Date: Mar 2008
Location: Alabama
Posts: 169
Default Re: Pulling the body for paint

That is a great idea. Were all the lock nuts accessible without too much foul language?
Timbeaux38 is offline  
 
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas EZGO > Ezgo Gas Tech


Thread Tools
Display Modes


Similar Threads
Thread Forum
paint Body and Paint
G2 paint Gas Yamaha
not pulling gas and engine stumbles Gas Yamaha
Paint me up!! Lifted Golf Carts


All times are GMT -5. The time now is 11:20 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.