|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-15-2023, 09:52 AM | #1 |
Not Yet Wild
Join Date: Oct 2021
Location: England
Posts: 46
|
Curtis 1268 wiring
Hi, I am installing a Curtis 1268 in an ezgo Rxv shell.
There is a connection j17 on the low side of the contactor, Novice question does this j17 connect to the large 48v +ve pole, Or the small -ve connection on the contactor AE4BC061-E81B-41C5-BB63-EE7B37529981.jpg Thanks |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-15-2023, 11:00 AM | #2 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,188
|
Re: Curtis 1268 wiring
J1-17 should be the ground for the coil activation circuit.
Page 14 https://cdn.curtisinstruments.com/pr..._manual_en.pdf |
03-15-2023, 01:17 PM | #3 |
Not Yet Wild
Join Date: Oct 2021
Location: England
Posts: 46
|
Re: Curtis 1268 wiring
Great rapid response thanks!
Can I ask another one? I am trying to use the Rxv three wire throttle Orange,black,yellow I assumed orange power Black ground Yellow wiper But no go The accelerator on/0ff, two wires do I connect Red to 48v and blue to controller Nearly there👍 |
03-16-2023, 07:40 AM | #4 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,188
|
Re: Curtis 1268 wiring
Not sure how but in the original configuration orange is 5v, black is ground, yellow is wiper
|
03-16-2023, 02:45 PM | #5 |
Not Yet Wild
Join Date: Oct 2021
Location: England
Posts: 46
|
Re: Curtis 1268 wiring
That’s great thanks, that is how I had it setup. The controller pin on pot high only reads 0.61v. I have tried a 4 wire ohms throttle but still nothing.
Key on - 48v to where it’s meant to be. R and F show 48v when selected. The contactor has 48v on both post if it’s engaged or not, but there is a resistor between the posts so probably correct. B+ reads 48v and so does M with contactor in or out. I have not had any led flashing it seems dead. The |
03-18-2023, 03:40 PM | #6 |
Not Yet Wild
Join Date: Oct 2021
Location: England
Posts: 46
|
Re: Curtis 1268 wiring
Ok so nothing,
I have acquired a Curtis 1313 handheld, It comes up with no system detected. I have pack voltage to contactor, B+ and M+ Is the controller bad or is there a trick to waking it up. |
03-19-2023, 02:14 AM | #7 |
British born Nincompoop
Join Date: Feb 2007
Location: United Kingdom
Posts: 2,463
|
Re: Curtis 1268 wiring
The handheld is either not seeing the controller due to a bad or broken connection or the controller is dead. These are the only times I have encountered this. Last time, it was a broken wire in my handheld cable at the plug.
|
03-20-2023, 09:05 AM | #8 |
Not Yet Wild
Join Date: Oct 2021
Location: England
Posts: 46
|
Re: Curtis 1268 wiring
Great thanks, some person put J4 in J3 now corrected, I have power!
I am getting a 2:4 warning message. Contactor low, when I turn the key on the contactor clicks. I have 48v where I think it should be. With the resistor between both sides of the contactor it always reads 48v is there a way to test it. I need to read more how to diagnose faults with the 1313 |
03-20-2023, 03:45 PM | #9 |
Not Yet Wild
Join Date: Oct 2021
Location: England
Posts: 46
|
Re: Curtis 1268 wiring
https://www.youtube.com/watch?v=Fn-UHhWS2D0
I have taken a video is my contactor wired up right? Thanks |
|
|
Similar Threads | ||||
Thread | Forum | |||
Curtis 1268-5411 5,5 | Electric EZGO | |||
EZGO PDS Curtis 1268 Wiring Diagram | Electric EZGO | |||
FS: Curtis 1268 Controller | Golf Carts and Parts | |||
1268 curtis | Electric Club Car | |||
Need help wiring Curtis controller 1268-5403 | Electric Club Car |