|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
|
04-09-2013, 04:27 PM | #1 |
Getting Wild
Join Date: Apr 2012
Posts: 87
|
g1 oil mixing
ok just bought some quicksilver 2 stroke oil. I mix cause eliminated oil injection system. Was running yamalube at 65:1. I run quite abit down the road at full throttle. So what ratio should I mix this quick silver at? Im also going to buy a ratio rite mixing cup so I get it mixed right. I dont mind a lil rich cause im in country and do a bunch of road running full throtle. Also is that quick silver a decent 2stroke oil to mix with?
|
04-09-2013, 04:44 PM | #2 |
Gone Wild
Join Date: Dec 2012
Location: E. Wallyworld Vermont
Posts: 234
|
Re: g1 oil mixing
There are a few different blends of QS oil from straight dino to full synthetic, Which are you going with. This may not make a big difference but the full synthetic can generally be run a bit leaner.
And yes they are good oils, So is Yamalube which I would run if I could get some here. I will let others with more premix experience take this, I am more experienced with injection. |
04-09-2013, 05:07 PM | #3 |
Getting Wild
Join Date: Apr 2012
Posts: 87
|
Re: g1 oil mixing
im not sure if it is full synthetic. Its premium 2-cycle outboard oil. Like I said I run a bunch on road full throttle. So wht ratio should I run?
|
04-09-2013, 06:01 PM | #4 |
Gone Wild
Join Date: Dec 2012
Location: E. Wallyworld Vermont
Posts: 234
|
Re: g1 oil mixing
To me the 65:1 you were running is not the wrong thing to stay with.
Where some guys are saying 130 or so would scare me pretty bad for an engine that will be wrung out. Those lean mixture may be fine for a fleet of golf carts loafing about some fairways. |
04-09-2013, 06:22 PM | #5 |
I Refuse To Get Stuck!!!
Join Date: Jun 2010
Location: Hilton,NY
Posts: 5,427
|
Re: g1 oil mixing
I don't know what Yamaha suggests,but Ez-Go wanted 128:1 (1oz./gal)stock,and most people including myself run 100:1(1-1/2oz.) with no issues.Mine had the snot beat out of it,mostly wide open for 4yrs. and still runs good.Never had any issues with lean/hot.The plug was always perfect.
|
04-09-2013, 08:42 PM | #6 |
Getting Wild
Join Date: Apr 2012
Posts: 87
|
Re: g1 oil mixing
I think ill run 2oz to 1gal.
|
04-09-2013, 08:47 PM | #7 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: g1 oil mixing
Manual says the oil injector mixes at 150:1 at low speeds, and 300:1 at high speeds. Most of us are scared to try that, but I think 50:1 is just too much oil. I run 80:1 and it smokes a little bit at slow speeds. I think the right premix would be between 80:1 and 120:1 somewhere.
Keep in mind.....the more oil you use, the less gas will be in the mix. With less gas you will run leaner, sometimes leaner means less power. Leaner also means more heat in the combustion chamber, more detonation, and possibly piston failure? More oil isn't always better. My 2 cents. |
04-10-2013, 05:37 AM | #8 | |
Gone Wild
Join Date: Dec 2012
Location: E. Wallyworld Vermont
Posts: 234
|
Re: g1 oil mixing
Quote:
|
|
04-10-2013, 06:02 AM | #9 |
Gone Wild
Join Date: Dec 2012
Location: Maine
Posts: 184
|
Re: g1 oil mixing
I was told that yamaha 2 strokes are 100:1, with 25:1 for break-in. I was asked were I got my mix rate from when I said I was running 85:1
|
04-10-2013, 06:21 AM | #10 |
Gone Wild
Join Date: Dec 2012
Location: E. Wallyworld Vermont
Posts: 234
|
Re: g1 oil mixing
I guess I run richer mixes in my chainsaw fuel than I need to.
I think back a number of years when for a short period ran Amsoil in my weed wacker at around 100:1 or so. I really do not recall but I do know the weed wacker bruised my hip when it seized. It was replaced with a 4 stroke. I expect that weed wacker was jetted lean which with a lean oil ratio meant the engine was starving for oil. |
|
|
Similar Threads | ||||
Thread | Forum | |||
Yamaha g2 gas mixing into my oil | Gas Yamaha | |||
Mixing oil and Gas G1 | Gas Yamaha | |||
gas and oil mixing in carb | Gas EZGO | |||
Mixing new batts with old? | Electric EZGO | |||
I'm a new member?? mixing 6V.&12V. | Electric Club Car |