Programming Curtis Controller

[georgia088]

Originally Posted by TheCartBoy

Was suggesting to use the PC software so you can see the options beyond OEM access. I was also assuming you only had a 1313 handset.

The file is invalid. I couldn't get it to post. I can see all of the settings that the manual says this controller has.... except the next to last setting is missing "DRV OVRCUR DIS" I don't know how to find it. I have oem access on the pc software.

Thanks.

[georgia088]

AH! ok. I got the spreadsheet, but it doesn't show the setting either in the spread sheet..

Menu 1 Menu 2 Menu 3 Menu 4 Menu 5 Menu 6 Menu 7 Value Min Max Unit Read Access Write Access
Program
M1 MAIN C/L 400 100 400 OEM OEM
M2 MAIN C/L 400 100 400 OEM OEM
REGEN C/L 200 50 400 OEM OEM
PLUG C/L 200 50 400 OEM OEM
AUX DRVR MODE 0 0 2 OEM OEM
AUX PULL IN 1 1 3 OEM OEM
AUX HOLDING 1 1 3 OEM OEM
EMB DELAY 1.4 0 5 OEM OEM
FLD BRAKE On Off On OEM OEM
FLD BRAKE SPD 1.2 0 6 OEM OEM
FLD BRAKE MAX 0.5 0 50 OEM OEM
FLD BRAKE RATE 5 0 6 OEM OEM
EMB SPD CHECK On Off On OEM OEM
EMB SPD VALUE 0.4 0 40 OEM OEM
RPM TO SPEED 113 20 255 OEM OEM
TACHO POLES 4 4 20 OEM OEM
MODE AFTER KEY On Off On OEM OEM
WARNING OPTION 3 0 7 OEM OEM
M1 FWD SPEED 35 4 40 OEM OEM
M1 ACCEL 1.6 0.6 5 OEM OEM
M1 DECEL 5 0.2 10 OEM OEM
M1 BRAKE MIN 10 10 100 OEM OEM
M1 BRAKE MAX 20 10 100 OEM OEM
M1 BRAKE MAP 22.5 20 80 OEM OEM
M1 BRAKE START 5 0 40 OEM OEM
M1 BRAKE END 9 0 40 OEM OEM
REV SPEED 12 4 16 OEM OEM
REV ACCEL 3.2 0.6 5 OEM OEM
REV DECEL 3 0.2 10 OEM OEM
REV BRAKE MIN 10 10 100 OEM OEM
REV BRAKE MAX 25 10 100 OEM OEM
REV BRAKE MAP 20 20 80 OEM OEM
REV BRK START 1.4 0 40 OEM OEM
REV BRAKE END 4 0 40 OEM OEM
M2 FWD SPEED 18.2 5.6 40 OEM OEM
M2 ACCEL 1.6 0.6 5 OEM OEM
M2 DECEL 5 0.6 10 OEM OEM
M2 BRAKE MIN 10 10 100 OEM OEM
M2 BRAKE MAX 20 10 100 OEM OEM
M2 BRAKE MAP 22.5 20 80 OEM OEM
M2 BRAKE START 5 0 40 OEM OEM
M2 BRAKE END 9 0 40 OEM OEM
OVERVOLTAGE 62 40 65 OEM OEM
LOW VOLTAGE 37.5 27 42 OEM OEM
THROTTLE MAP 20 20 80 OEM OEM
THROTTLE 0% 1.4 0 2 OEM OEM
THROTTLE 100% 3.9 2.1 5 OEM OEM
THROT FAULT LO 0 0 2 OEM OEM
THROT FAULT HI 5 3 5 OEM OEM
M1 FWD FLD MIN 3 2 15 OEM OEM
REV FIELD MIN 5.5 2 15 OEM OEM
M2 FWD FLD MIN 4.5 2 15 OEM OEM
FLD MAP START 100 0 200 OEM OEM
FIELD RAMP 50 20 80 OEM OEM
FIELD MAX 30 20 50 OEM OEM
FIELD MAP END 325 200 400 OEM OEM
NEG FLD MAP START 80 0 200 OEM OEM
NEG FLD RAMP 50 20 80 OEM OEM
NEG FIELD MAX 23 10 50 OEM OEM
NEG FLD MAP END 300 200 400 OEM OEM
WALKAWAY C/L 15 6 25 OEM OEM
KSI SRO ENABLE Off Off On OEM OEM



The spread sheet file is invalid too. Here is a copy and paste. I can delete it if it takes up too much room.

[broke 20]

Hey guys...new to the Curtis programmer and just have a quick question. 2020 Club Car Tempo, when I flash speed code 4 with the programmer, should my max speed setting change to reflect 19mph? The A,B,C codes save normally, toggle the tow switch and I am showing speed code 4 "installed", but my max speed setting cannot be adjusted from 14.8. Thanks in advance.