lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV.



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 01-09-2020, 04:49 PM   #1
jreue
Not Yet Wild
 
Join Date: Jun 2014
Posts: 31
Default Mock Install: Alltrax SR48500 Controller, 400a Solenoid, SW202 Reversing Contactor

This thread is based off of my recent thread where I had an issue with my 95' EZGO Medalist which stopped working. I tracked it down to my speed controller being fried. Read about that story here.

The end result was getting in contact with scottyb over at https://www.cartsunlimited.net/. I ended up ordering "Item #4" in his Speed Controller packages which included the following:
  • Alltrax SR48500 Speed Controller
  • 400a Solenoid
  • SW202 Reversing Contactor
  • 2g cable set

ScottyB had it shipped out super quick and I was really excited to get the build underway. During the wait, I pulled out my old controller, solenoid, F/R switch, batteries, and cleaned up the cart in preparation. Also, while waiting, I attempted to research as much as possible so I'd be ready for this install. I watched a few videos, read what I could find, but I still had some questions. It's one thing to watch someone else do it, look at pictures, look at wiring diagrams, but sometimes its just not all that clear.

One main thing I found was that although some diagrams, pictures, explanations, just didn't full 'show' what I was needing. Some of these wiring diagrams have multiple connection terminals and the diagrams are not always perfectly clear as to where exactly a wire goes. Some folks take pictures/videos of the inside of their carts, but I always felt like it wasn't capturing what I needed.

So, I thought I do a mock install, sort of a bench dry run of the install... If anything it helped me understand the combination of scottyb's install instructions (shout out scottyb), actual documentation, and various other install pictures/videos. Furthermore, I sure hope it helps someone else in this community who may perhaps be struggling with their install, or maybe a little apprehensive to try the upgrade.

** If anyone see's anything "technically" wrong with the wiring mockup, lemme know and I'll correct. The main purpose behind this thread is not only to inform others of the wiring, but to give me a dry run before I accidentally blow something up. :)

So here we go!

Here are all the parts I got in my package. Even got a sticker!


In the package we get the required resistor and diodes, but we have to crimp the terminal connectors on. The connectors are all included in the package. Lets do that now.

Here is our resistor that I crimped the ring terminals on.


Now we just screw that resistor on the solenoid like this.


Next we need a diode attached to the solenoid. The polarity has to be correct here. Look for the stripe on the diode. That's (+)


Crimp those connectors on!


Now lets attach it to our solenoid. Bam!


Now lets work on our Reversing Contactor switch. We need 2 diodes here.
Make sure the polarity is correct!


Crimped and ready


Now we attach them to our Reversing Contactor. On each side there are some blade terminals. Attach 1 on each side.
Here is one side...


Here is the other side...


Now....We have our solenoid and reversing contactor ready. Let's mock this install....

With a few cardboard boxes and some colored pipe cleaners, this is what I have for 'control' wiring. I think this is pretty cool as you can clearly see where all wires actually go. All the colors match what is in my EZGO cart, except for purple, which is suppose to be black...the store was out of black...

A much higher resolution version HERE

Now lets add our motor with its 2a wires

A much higher resolution version HERE


And finally lets hook this thing up to some our battery pack! BAM!

A much higher resolution version HERE

Hope you all enjoy
jreue is offline   Reply With Quote
 
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO


Thread Tools
Display Modes


Similar Threads
Thread Forum
WTB: 48V SW202 Reversing Contactor Golf Carts and Parts
FS: 48V SW202 Reversing Contactor Golf Carts and Parts
Alltrax Controller and 400a Solenoid Install Help Electric Club Car
SW202 reversing contactor and Alltrax AXE controller Electric EZGO
Reversing Contactor not working? EZGO TXT 48V w/SW202 Contactor. How to test it? Electric EZGO


All times are GMT -5. The time now is 02:53 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.