2008 President wont go after stopping

Salado Bill · 11-05-2018, 04:51 PM

I am working on a buddy's 2008 C/C President, serial #PH0835-952998. Looks like the OBC has been removed and it has a grey aftermarket motor that is a 6hp max peak 18 hp. Has curtis 350 amp controller and stock solenoid. After a while when you stop with the key on you have to turn the key back on and off for it to go. Batteries are new and cables tight and good. Any idea's on where to look as we have replaced the MCOR already.

TahoeDawgZ71 · 11-05-2018, 06:29 PM

You'd have to have a Curtis handheld scanner to do it, but it sounds like you need to turn off the KSI ENABLE function.

Salado Bill · 11-06-2018, 07:29 AM

I have a FSIP Curtis handheld. But I can't find the plug in on this cart. Also what is the KSI function and how do you get to it?

NoleFan4Ever · 11-06-2018, 08:12 AM

Key Switch Input. It should be located under the drivers side of the seat and utilizes a rubber tie-wrap to secure it between or beside the battery. (Not sure if you have 4-12's or 6-8's)

It is simply a small 4 wire round plug (rubber cover looks like a top-hat) that runs back to the controller for its interface.

TahoeDawgZ71 · 11-06-2018, 09:06 AM

It's not KSI... I don't know why I said that. What you're looking for is "Keyswitch SRO". I wasn't thinking clearly last night when I posted that in the midst of all the kids screaming and dogs barking. Sorry.

Salado Bill · 11-06-2018, 01:14 PM

Tow Dawg I understand. It looks like they cut the connector off, I don't know why because the only thing I can find is a 6-pin connector that has been cut that has a red, yellow, blue, brown, white, and purple wire where it feeds into the loom. The brown wire is the only one still connected. I'm not sure if this is were it's supposed to be?

Salado Bill · 11-06-2018, 01:15 PM

Sorry about the Tow Dawg, Tahoedawg.

Sergio · 11-06-2018, 01:25 PM

The program port is under the dash near the key Switch.

You can also use the 4-pin molex programmer connector directly on the Controller ( If You don't see it, what is the Controller model #?).

The option name is: KSI SRO ENABLE

Check for errors in case the KSI cycle is not the issue but it is needed to clear other error conditions.

Salado Bill · 11-06-2018, 01:55 PM

There is no plug on the controller, the model number is 1234 5371 (3781 45371) I found a square molex connector behind the dash with four wires , red/white, green, brown/white, black/white. I'm not sure if this the one as they removed the round four pin by the bottom of the key switch.

Sergio · 11-06-2018, 02:12 PM

Is this an AC Controller?

11-05-2018, 04:51 PM	#1
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22	2008 President wont go after stopping I am working on a buddy's 2008 C/C President, serial #PH0835-952998. Looks like the OBC has been removed and it has a grey aftermarket motor that is a 6hp max peak 18 hp. Has curtis 350 amp controller and stock solenoid. After a while when you stop with the key on you have to turn the key back on and off for it to go. Batteries are new and cables tight and good. Any idea's on where to look as we have replaced the MCOR already.
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22

11-05-2018, 06:29 PM	#2
TahoeDawgZ71 revolutiongolfcars.com Join Date: Mar 2010 Location: Golf Car Capital of The World... Augusta, Georgia Posts: 10,224	Re: 2008 President wont go after stopping You'd have to have a Curtis handheld scanner to do it, but it sounds like you need to turn off the KSI ENABLE function.

11-06-2018, 07:29 AM	#3
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22	Re: 2008 President wont go after stopping I have a FSIP Curtis handheld. But I can't find the plug in on this cart. Also what is the KSI function and how do you get to it?
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22

11-06-2018, 08:12 AM	#4
NoleFan4Ever MOD of all BS! Join Date: Sep 2011 Location: Florida Posts: 17,477	Re: 2008 President wont go after stopping Key Switch Input. It should be located under the drivers side of the seat and utilizes a rubber tie-wrap to secure it between or beside the battery. (Not sure if you have 4-12's or 6-8's) It is simply a small 4 wire round plug (rubber cover looks like a top-hat) that runs back to the controller for its interface.

11-06-2018, 09:06 AM	#5
TahoeDawgZ71 revolutiongolfcars.com Join Date: Mar 2010 Location: Golf Car Capital of The World... Augusta, Georgia Posts: 10,224	Re: 2008 President wont go after stopping It's not KSI... I don't know why I said that. What you're looking for is "Keyswitch SRO". I wasn't thinking clearly last night when I posted that in the midst of all the kids screaming and dogs barking. Sorry.

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

11-06-2018, 01:14 PM	#6
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22	Re: 2008 President wont go after stopping Tow Dawg I understand. It looks like they cut the connector off, I don't know why because the only thing I can find is a 6-pin connector that has been cut that has a red, yellow, blue, brown, white, and purple wire where it feeds into the loom. The brown wire is the only one still connected. I'm not sure if this is were it's supposed to be?
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22

11-06-2018, 01:15 PM	#7
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22	Re: 2008 President wont go after stopping Sorry about the Tow Dawg, Tahoedawg.
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22

11-06-2018, 01:25 PM	#8
Sergio Gone Wild Join Date: Sep 2012 Location: Charlotte, NC Posts: 9,329	Re: 2008 President wont go after stopping The program port is under the dash near the key Switch. You can also use the 4-pin molex programmer connector directly on the Controller ( If You don't see it, what is the Controller model #?). The option name is: KSI SRO ENABLE Check for errors in case the KSI cycle is not the issue but it is needed to clear other error conditions.

11-06-2018, 01:55 PM	#9
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22	Re: 2008 President wont go after stopping There is no plug on the controller, the model number is 1234 5371 (3781 45371) I found a square molex connector behind the dash with four wires , red/white, green, brown/white, black/white. I'm not sure if this the one as they removed the round four pin by the bottom of the key switch.
Salado Bill Not Yet Wild Join Date: Jul 2016 Posts: 22

11-06-2018, 02:12 PM	#10
Sergio Gone Wild Join Date: Sep 2012 Location: Charlotte, NC Posts: 9,329	Re: 2008 President wont go after stopping Is this an AC Controller?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
2008 Precedent 48v wont move	Electric Club Car
2008 club car president: clearance for 205-65-10 tires	Electric Club Car
2008 Turf 2 starting then stopping	Electric Club Car
2008 precedent wont charge	Gas Club Car
05 president wont roll in tow mode and wont run at wot	Electric Club Car