|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
11-24-2020, 01:10 PM | #1 |
Gone Wild
Join Date: Sep 2013
Location: Alabama
Posts: 772
|
Alignment Idiot Award - I Deserve It
Hate to admit I did this but I can't be the only one.
Tires were out of alignment so I decided it was time to replace old front-end parts. Sanded, applied rust converted where needed and painted. Found no damaged/bent parts. Replaced all the bushings and stems. New king pins, wave washers, tie rod ends. Had another senior moment and only ordered 2 steering stem bushings so replaced the ones on the right only. Will order two more for left. Replaced hub bearings with new Timken bearings. They are sooo smooth. New leaf spring adjustment eccentric. Torqued everything to specs. I was proud of my work! Put the tires on, finger tighten lug nuts, lowered cart to the floor. Loosened the 4 bolts that hold the leaf spring and loosened the adjustment eccentric. Used large square and calipers to check and correct the camber. It was perfect! No more right tire leaning out. Then measured and began to set toe in. Left tire still not toeing correctly. My frustration grew and I put down my tools and called it a night. As I was walking away, it hit me! I failed to tighten the tire lugs after I took the cart off the jack stands. I can do really dumb things. Now, I get to start all over with the alignment, right?? When I tighten the lug nuts won't it effect the camber that I set?? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-24-2020, 01:17 PM | #2 |
Gone Wild
Join Date: Sep 2010
Posts: 879
|
Re: Alignment Idiot Award - I Deserve It
well , in your defense , ............ i got nothin'........ i always just use the "beer" excuse ....
|
11-24-2020, 02:00 PM | #3 | |
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: Alignment Idiot Award - I Deserve It
Quote:
As far as DA things done, I usually get the DA of the year award. |
|
11-24-2020, 05:22 PM | #4 |
Gone Wild
Join Date: Apr 2020
Location: Hurricane, Utah
Posts: 2,802
|
Re: Alignment Idiot Award - I Deserve It
I think you may have laughed at me a while back, so out of respect I am laughing at you now :)
|
11-24-2020, 09:17 PM | #5 |
Gone Wild
Join Date: Sep 2013
Location: Alabama
Posts: 772
|
Re: Alignment Idiot Award - I Deserve It
|
11-24-2020, 09:23 PM | #6 | |
Gone Wild
Join Date: Sep 2013
Location: Alabama
Posts: 772
|
Re: Alignment Idiot Award - I Deserve It
Quote:
Can't imagine you ever getting THAT award. Thanks for the encouragement! I won't get to work on the cart again until Thursday night or Friday. I'll let you know how it goes. |
|
11-24-2020, 09:26 PM | #7 | |
Gone Wild
Join Date: Sep 2013
Location: Alabama
Posts: 772
|
Re: Alignment Idiot Award - I Deserve It
Quote:
Go ahead and laugh. I deserve your payback. |
|
11-24-2020, 10:18 PM | #8 | |
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: Alignment Idiot Award - I Deserve It
Quote:
|
|
11-25-2020, 12:16 AM | #9 |
Gone Wild
Join Date: Nov 2016
Location: near Calgary, AB, Canada
Posts: 1,516
|
Re: Alignment Idiot Award - I Deserve It
If your wheel nuts were reasonably tight, then your camber measurement should be correct.
If the wheel nuts were sloppy and the wheel was not properly seated on the hub, your camber measurement may be out a bit. What method are you using to measure the camber? I ran across this video that uses a plumb bob to measure the camber ... it appears to be a pretty accurate method since a plumb bob always provides an accurate vertical reference line (as long the wind is not blowing in your work space). The calculation they show in the video is incorrect (as pointed out in one of the comments) ... you should use Sine in the formula instead of Tangent ... but at low inclinations it does not matter much. See the video here: https://www.youtube.com/watch?v=kT1eK55ZhJo No idiot award given for this minor indiscretion ... that's part of life. |
11-25-2020, 12:44 AM | #10 | |
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: Alignment Idiot Award - I Deserve It
Quote:
As far as the award goes, this coveted recognition will not go to CCNorth. It is reserved for those with much greater capacity and frequency for messing things up. |
|
Tags |
alignment, camber, tires, toein |
|
|
Similar Threads | ||||
Thread | Forum | |||
Dumb *** Award goes to....... | Electric Club Car | |||
DUMAS award nominee… myself | Electric Club Car |