lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Modified Golf Carts > Design Center
Design Center Shop tools, fabrication and Paint and Body



Post New Thread  Reply
 
Thread Tools Display Modes
Old 11-21-2018, 06:27 AM   #11
Jkerle
Gone Wild
 
Jkerle's Avatar
Club Car
 
Join Date: Jul 2017
Location: West Columbia Texas
Posts: 1,036
Default Re: 3D printer thread

Quote:
Originally Posted by Winston Ellis View Post
Can you share the stl for that mirror mount?


Sent from my iPhone using Tapatalk
I'll post them up a bit later today I need my computer to do it.

Sent from my SM-G935V using Tapatalk
Jkerle is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 11-21-2018, 06:28 AM   #12
Winston Ellis
Gone Wild
 
Winston Ellis's Avatar
Club Car
 
Join Date: Oct 2018
Posts: 587
Default Re: 3D printer thread

Quote:
Originally Posted by Jkerle View Post
I'll post them up a bit later today I need my computer to do it.

Sent from my SM-G935V using Tapatalk


Thanks!


Sent from my iPhone using Tapatalk
Winston Ellis is online now   Reply With Quote
Old 11-21-2018, 09:25 AM   #13
Jkerle
Gone Wild
 
Jkerle's Avatar
Club Car
 
Join Date: Jul 2017
Location: West Columbia Texas
Posts: 1,036
Default Re: 3D printer thread

Here is preview of the following files. 3dFilePrfeviews.jpeg

Sent from my SM-G935V using Tapatalk
Jkerle is offline   Reply With Quote
Old 11-21-2018, 09:28 AM   #14
Jkerle
Gone Wild
 
Jkerle's Avatar
Club Car
 
Join Date: Jul 2017
Location: West Columbia Texas
Posts: 1,036
Default Re: 3D printer thread

Hmm it's not allowing me to upload the files. Any one know what the size restrictions are?

I'll try and zip them when you down load the zip file you'll get all of them. Along with the preview pic above.

Sent from my SM-G935V using Tapatalk
Jkerle is offline   Reply With Quote
Old 11-21-2018, 09:44 AM   #15
Jkerle
Gone Wild
 
Jkerle's Avatar
Club Car
 
Join Date: Jul 2017
Location: West Columbia Texas
Posts: 1,036
Default Re: 3D printer thread

I think I got it!

CC= Club Car/Color Choice
5PM= 5 Panel mirror
DS= Driver Side
PS= Passenger Side

The 12v washer has an OD of 40mm and works great for over sized cut outs when installing USB power outlets. The name is funky in the pic but its the only washer file. The profile has a slight tapered edge.

Mirror mount holes are 7mm and due to 3D printing characteristics they may need cleaned up with a 1/4inn drill bit. I use 3 outlines when printing to allow safe up sizing of these holes. At 70% fill the parts are plenty strong enough to hold the mirror.

The precedent mounting holes are 4in on center and the mirror mount position is 3in low. Its as close to the factory mount position as I could get it.

Yamaha mounts have not been physically installed yet. The mounting holes are 3-9/16 on center spacing and the same 3inch drop.

I have not printed and installed the CCprecedent color choice mount yet. I'm printing the second to last piece of the first set now. Good chance it will need revised.
Attached Files
File Type: zip BGW3DPrintFiles.zip (520.1 KB, 0 views)
Jkerle is offline   Reply With Quote
Old 11-21-2018, 10:09 AM   #16
Winston Ellis
Gone Wild
 
Winston Ellis's Avatar
Club Car
 
Join Date: Oct 2018
Posts: 587
Default Re: 3D printer thread

Thanks so much!

Will any of these mirror mounts work on a DS?

Quote:
Originally Posted by Jkerle View Post
I think I got it!

CC= Club Car/Color Choice
5PM= 5 Panel mirror
DS= Driver Side
PS= Passenger Side

The 12v washer has an OD of 40mm and works great for over sized cut outs when installing USB power outlets. The name is funky in the pic but its the only washer file. The profile has a slight tapered edge.

Mirror mount holes are 7mm and due to 3D printing characteristics they may need cleaned up with a 1/4inn drill bit. I use 3 outlines when printing to allow safe up sizing of these holes. At 70% fill the parts are plenty strong enough to hold the mirror.

The precedent mounting holes are 4in on center and the mirror mount position is 3in low. Its as close to the factory mount position as I could get it.

Yamaha mounts have not been physically installed yet. The mounting holes are 3-9/16 on center spacing and the same 3inch drop.

I have not printed and installed the CCprecedent color choice mount yet. I'm printing the second to last piece of the first set now. Good chance it will need revised.
Winston Ellis is online now   Reply With Quote
Old 11-21-2018, 10:13 AM   #17
Jkerle
Gone Wild
 
Jkerle's Avatar
Club Car
 
Join Date: Jul 2017
Location: West Columbia Texas
Posts: 1,036
Default Re: 3D printer thread

I would think so but you will need to measure the mounting holes to be sure. They mount to the front roof struts using the 2 bolts that secure the roof. Due to thickness of the mount the bolts may need to be replaced with 1-3/4in 1/4- 20 bolts. I can adjust the holes for you if needed and then we will have a DS file for anyone to use.

Sent from my SM-G935V using Tapatalk
Jkerle is offline   Reply With Quote
Old 11-30-2018, 11:00 AM   #18
Winston Ellis
Gone Wild
 
Winston Ellis's Avatar
Club Car
 
Join Date: Oct 2018
Posts: 587
Default Re: 3D printer thread

Quote:
Originally Posted by Jkerle View Post
I would think so but you will need to measure the mounting holes to be sure. They mount to the front roof struts using the 2 bolts that secure the roof. Due to thickness of the mount the bolts may need to be replaced with 1-3/4in 1/4- 20 bolts. I can adjust the holes for you if needed and then we will have a DS file for anyone to use.

Sent from my SM-G935V using Tapatalk
I`m having issues opening the STl in Solidworks. It looks like they are not to scale. Any ideas?
Winston Ellis is online now   Reply With Quote
Old 11-30-2018, 11:08 AM   #19
Jkerle
Gone Wild
 
Jkerle's Avatar
Club Car
 
Join Date: Jul 2017
Location: West Columbia Texas
Posts: 1,036
Default Re: 3D printer thread

Quote:
Originally Posted by Winston Ellis View Post
I`m having issues opening the STl in Solidworks. It looks like they are not to scale. Any ideas?
Give me a few minutes but what is the normal file type for solid works?

Sent from my SM-G935V using Tapatalk
Jkerle is offline   Reply With Quote
Old 11-30-2018, 11:14 AM   #20
Winston Ellis
Gone Wild
 
Winston Ellis's Avatar
Club Car
 
Join Date: Oct 2018
Posts: 587
Default Re: 3D printer thread

Solidworks likes to use .SLDPRT.

What did your create the files in?
Winston Ellis is online now   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Modified Golf Carts > Design Center


Thread Tools
Display Modes



All times are GMT -5. The time now is 10:12 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2023, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.