Clutch problem

jadawg27 · 06-30-2009, 04:45 PM

Ok I figured out the the clutch is not always disengaging so when I stop and try to take off again its stuck at where it should be in high speed and jerks me around. What should I do? Why would it not disengage all the time?

adrummer · 07-02-2009, 09:36 AM

It sounds like a problem i had. It could be the roller collars in the clutch assembely. they get worn out and out of round and cause the weights to become stuck, not allowing thr clutch to disengage.

jadawg27 · 07-02-2009, 03:38 PM

Yeah it is the rollers. did you replace them or did you get a new clutch?

adrummer · 07-02-2009, 04:16 PM

I replaced them. It was cheaper. It was a little tricky to take apart but not too difficult. I used a three jaw puller to remove the clutch and creatively used 2 pipe wrenches to remove the top end of the clutch assembly so the roller pins could be removed. it was a piece of cake to re-instal and runs like new

jadawg27 · 07-03-2009, 11:24 AM

So all and all its not super hard to do? I was debating on just buying a new clutch but don't really have the money. So if you say its not that hard I will try it. Thanks for the help Jason

adrummer · 07-05-2009, 04:29 PM

Right on. let me know if you run into any problems i can try to help.

06-30-2009, 04:45 PM	#1
jadawg27 Gone Wild Join Date: Apr 2009 Location: peotone IL Posts: 320	Clutch problem Ok I figured out the the clutch is not always disengaging so when I stop and try to take off again its stuck at where it should be in high speed and jerks me around. What should I do? Why would it not disengage all the time?

07-02-2009, 09:36 AM	#2
adrummer Not Yet Wild Join Date: Jun 2009 Posts: 4	Re: Clutch problem It sounds like a problem i had. It could be the roller collars in the clutch assembely. they get worn out and out of round and cause the weights to become stuck, not allowing thr clutch to disengage.
adrummer Not Yet Wild Join Date: Jun 2009 Posts: 4

07-02-2009, 03:38 PM	#3
jadawg27 Gone Wild Join Date: Apr 2009 Location: peotone IL Posts: 320	Re: Clutch problem Yeah it is the rollers. did you replace them or did you get a new clutch?

07-02-2009, 04:16 PM	#4
adrummer Not Yet Wild Join Date: Jun 2009 Posts: 4	Re: Clutch problem I replaced them. It was cheaper. It was a little tricky to take apart but not too difficult. I used a three jaw puller to remove the clutch and creatively used 2 pipe wrenches to remove the top end of the clutch assembly so the roller pins could be removed. it was a piece of cake to re-instal and runs like new
adrummer Not Yet Wild Join Date: Jun 2009 Posts: 4

07-03-2009, 11:24 AM	#5
jadawg27 Gone Wild Join Date: Apr 2009 Location: peotone IL Posts: 320	Re: Clutch problem So all and all its not super hard to do? I was debating on just buying a new clutch but don't really have the money. So if you say its not that hard I will try it. Thanks for the help Jason

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

07-05-2009, 04:29 PM	#6
adrummer Not Yet Wild Join Date: Jun 2009 Posts: 4	Re: Clutch problem Right on. let me know if you run into any problems i can try to help.
adrummer Not Yet Wild Join Date: Jun 2009 Posts: 4

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
G1 Clutch problem?	Gas Yamaha
clutch problem	Gas EZGO
Clutch problem?????	Gas EZGO
Clutch Problem	Gas EZGO