|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-10-2021, 05:46 PM | #11 |
Gone Wild
Join Date: Jul 2010
Location: Peachtree City, Ga.
Posts: 2,759
|
Re: Motor Break fail? 2016 RXV
OP, I'm wondering if you left a part (insert for the one on the right) on the motor. ? Somebody sells one like that but there is an insert that makes the oblong hole like the one on the left
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-10-2021, 05:50 PM | #12 |
Gone Wild
Join Date: Sep 2020
Location: Germany
Posts: 2,000
|
Re: Motor Break fail? 2016 RXV
New one looks totaly right, old one broken apart? Check If the middle part is still on the armature...
|
05-10-2021, 06:00 PM | #13 |
Getting Wild
Join Date: May 2011
Location: Lantana, TX
Posts: 95
|
Re: Motor Break fail? 2016 RXV
|
05-10-2021, 06:07 PM | #14 |
Gone Wild
Join Date: Jul 2010
Location: Peachtree City, Ga.
Posts: 2,759
|
Re: Motor Break fail? 2016 RXV
Yes, that's why I think the insert is still on the motor. The new one you have should be correct. The one from country cat is way too expensive.
|
05-10-2021, 06:08 PM | #15 |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: Motor Break fail? 2016 RXV
|
05-10-2021, 06:37 PM | #16 | |
Getting Wild
Join Date: May 2011
Location: Lantana, TX
Posts: 95
|
Re: Motor Break fail? 2016 RXV
Quote:
Trevor |
|
05-10-2021, 07:17 PM | #17 |
Getting Wild
Join Date: May 2011
Location: Lantana, TX
Posts: 95
|
Re: Motor Break fail? 2016 RXV
okay new motor break installed, followed the directions from kernal and the cart still wont run. switching from off to R or F I hear two clicks but not the typical third if I recall correctly. not sure if the third is the break release?
Thoughts? Thanks Trevor |
05-10-2021, 09:55 PM | #18 |
Getting Wild
Join Date: May 2011
Location: Lantana, TX
Posts: 95
|
Re: Motor Break fail? 2016 RXV
One correction about following directions, I don’t recall what the key position was when I removed the old unit since it was late, dark, and I didn’t knew at the time it might matter.
|
05-11-2021, 04:20 AM | #19 |
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,238
|
Re: Motor Break fail? 2016 RXV
Replacing the Park Brake on an E-Z-GO RXV
Remove the two T27 torx screws on the rear cover Choke the wheels Disconnect the negative cable on the battery pack Turn the ignition key to reverse, wait till the reverse indicator becomes silent then turn key off Disconnect wire harness from motor brake Remove the three 10mm hex screws and lock washers from brake If bolts are rusty replace them Remove brake if there is residue on motor be sure to clean it use a wire brush Position the brake with the connector at the top, install the three hex screws loosely. Connect wire harness to the motor brake, re-connect battery negative cable Turn ignition to neutral, turn Run/Tow switch to Tow position, this provides power to the brake to align the disc material Set torque wrench between 53 to 65 in. lbs (6-8 Nm) and tighten screws be sure not to over tighten Turn key back to the off position Move Run/Tow switch back to Run position Put rear back cover on |
05-11-2021, 07:09 AM | #20 | |
Not Yet Wild
Join Date: Oct 2010
Posts: 17
|
Re: Motor Break fail? 2016 RXV
Quote:
What is wrong with the HD Switch brake that many seem to love or hate vs the OEM part. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
2014 EZGO RXV motor break | Electric EZGO | |||
After FSIP motor break in | Electric Club Car | |||
New motor break-in | Electric EZGO | |||
99 CC DS motor controller fail what do I need | Extreme DC! | |||
Motor break in | Gas Yamaha |