|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
07-09-2016, 02:17 PM | #1 |
Getting Wild
Join Date: Jul 2016
Location: Bucks County, PA
Posts: 120
|
Wiring Alltrax SR48500 to 2000 EZGo
I'm wiring up the new electronics. On this connector, it appears that I cut each and terminate with a spade. Then black goes black J1, orange to blue J1, and red to red J1 from solenoid correct? Does the white then go to J4?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-09-2016, 02:31 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Here is a step by step SR install in Ezgo TXT by me thread with pictures > http://www.buggiesgonewild.com/elect...r-install.html
|
07-09-2016, 02:31 PM | #3 |
Gone Wild
Join Date: Apr 2016
Location: Greenwood, SC
Posts: 1,291
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
I know when I did mine I had both the manual out and scottyb directions out and still asked a question or two in the process. My cart is a bit older and already had spades on the wires.
|
07-09-2016, 03:07 PM | #4 |
Getting Wild
Join Date: Jul 2016
Location: Bucks County, PA
Posts: 120
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Thanks fellas!
|
07-09-2016, 03:12 PM | #5 |
Getting Wild
Join Date: Jul 2016
Location: Bucks County, PA
Posts: 120
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Thanks fellas! Scotty I read that but I still don't see where the white wire goes? I can't see it in the photos either? And lastly, is the small black wire solenoid to B- needed on the new setup?
|
07-09-2016, 04:02 PM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
The white and black wires are the throttle signal. The diagram in the install manual shows the wires plugged in to pin J4 (white) and J5 (black)
I'll have to post a better picture like the one attached here. Noticed I have the white and black reversed But it seems to make no difference in the signal. Better swap mine around just to be safe. |
07-09-2016, 04:58 PM | #7 | |
Gone Wild
Join Date: Apr 2016
Location: Greenwood, SC
Posts: 1,291
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Quote:
|
|
07-09-2016, 05:36 PM | #8 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Thank you for that advice.
|
07-09-2016, 06:16 PM | #9 |
Getting Wild
Join Date: Jul 2016
Location: Bucks County, PA
Posts: 120
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Thanks all! Took a break. I'm pretty close! Either tonight or tomorrow I should have it finished up. I just don't want to make any mistakes. I very appreciate everyone's help! What about that black wire from solenoid to B-?
|
07-09-2016, 06:36 PM | #10 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Wiring Alltrax SR48500 to 2000 EZGo
Quote:
|
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
SR48500 Alltrax introduction thread | Announcements | |||
2000 EZGO Wiring help | Electric EZGO | |||
48v Ezgo TXT w/ Alltrax 4855 wiring diagram for dummie | Electric EZGO | |||
WTB: 2000 ezgo main low voltage wiring | Golf Carts and Parts | |||
Need help wiring Alltrax Controller on 1995 EZGO | Electric EZGO |