10-28-2019, 07:42 PM | #11 |
Not Yet Wild
Join Date: Oct 2019
Posts: 21
|
Re: 2000 Workhorse st350
There are new wires with the new coil and new plugs
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-28-2019, 08:16 PM | #12 |
Vintage tech
Join Date: Sep 2009
Location: South
Posts: 3,215
|
Re: 2000 Workhorse st350
CP241, I have three OEM coils and all have spark plug wires on them. Maybe he did change them ? I just noticed his last post and indeed he did change them
|
10-28-2019, 08:38 PM | #13 |
Not Yet Wild
Join Date: Oct 2019
Posts: 12
|
Re: 2000 Workhorse st350
The coils that I have used had the wires already on them!
|
10-28-2019, 09:37 PM | #14 |
Not Yet Wild
Join Date: Oct 2019
Posts: 21
|
Re: 2000 Workhorse st350
Take a look at this explanation---- Google-- copy and paste complete line below'
Powerdynamo, twin ignition coil fires only one side? |
10-28-2019, 11:22 PM | #15 |
Nincompoop village idiot
Join Date: Apr 2018
Location: Michigan
Posts: 9,673
|
Re: 2000 Workhorse st350
Ok sorry, I wasnt sure if the new coils came with wires or not. Are they OEM coils?
Maybe a long shot, and I dont know if that would donit or not, but maybe try running a ground strap directly to the ignitor body. I would think a bad ground would affect noth cylinders and not just 1, but it's easy enough that it's worth a shot. Out of curiosity, because I dont recall reading it, what spark plugs are you running? |
10-29-2019, 06:23 PM | #16 |
Not Yet Wild
Join Date: Oct 2019
Posts: 21
|
Re: 2000 Workhorse st350
NGK plugs
There are no OEM coils available I was told by 2 dealers I did wire wheel all grounds and new bolts. I will double check though. |
11-16-2019, 01:21 PM | #17 |
Not Yet Wild
Join Date: Oct 2019
Posts: 12
|
Re: 2000 Workhorse st350
I replaced the CDI Box for the 3rd time and reset the gap on the pulse pickup to .015 and it seemed to solve our problem maybe this could help you ,I know some aftermarket ignition parts do not work well !
|
11-16-2019, 10:37 PM | #18 |
Not Yet Wild
Join Date: Oct 2019
Posts: 21
|
Re: 2000 Workhorse st350
I just took my pickup coil off and do not know what it should ohm out at. This one is 232 ohms. There is no adjustment on my pickup coil.
I recently put in 2 new Chinese igniter coils both were junk found a used oem igniter got back to where I was firing on one side. Maybe it's the pickup coil? Do you know what the ohm range should be on good pick-up coil? thanks |
11-17-2019, 12:01 AM | #19 |
Vintage tech
Join Date: Sep 2009
Location: South
Posts: 3,215
|
Re: 2000 Workhorse st350
http://www.buggiesgonewild.com/gas-e...-question.html
Go to post #10. This pulser coil came off an engine that was running fine. Show hows to set it also on page 10 |
11-29-2019, 11:13 AM | #20 |
Not Yet Wild
Join Date: Oct 2019
Posts: 21
|
Re: 2000 Workhorse st350
Thank Everyone!
Checked gap on pick-up coil still no difference. (Tried .015 & .020) Still just getting spark on long wire off coil (it will fire either plug) and getting 12 volt to coil. Checked starter generator while turning over 14.5 volts. Put on used igniter box OEM no change. Grounds are cleaned and new added. Does anyone know what automotive coil would work this? The new coil has been tested ok but maybe not under load? |
Tags |
1 0f 2 coil firing |
|
|
Similar Threads | ||||
Thread | Forum | |||
2000 Workhorse ST350- blown engine replacement | Gas EZGO | |||
2000 workhorse st350 shocks | Gas EZGO | |||
2000 EZ GO workhorse st350 | Lifted Golf Carts | |||
2000 st350 workhorse | Gas EZGO | |||
2000 ST350 workhorse wiring diagram | Gas EZGO |