|
Design Center Shop tools, fabrication and Paint and Body |
|
Thread Tools | Display Modes |
11-20-2020, 04:54 PM | #1 |
Gone Wild
Join Date: Jul 2017
Location: Cape Coral FL
Posts: 243
|
Best type of blade for cutting aluminum pipe
Tile pretty much says it all. I've ok so far with a sawzall for straight cuts, but I was hoping to find a blade that would fit my 10" miter saw to help with the angled cuts.
Anyone have any suggestions. I'm open to anything, hopefully before I use up all my material |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-20-2020, 05:25 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Best type of blade for cutting aluminum pipe
For a radial type saw. The exact answer depends upon the diameter and rpm. But basically you want carbide teeth and lots of them.
And for God's sake be freking careful. If the pipe moves at all you will regret ever trying to cut it in this saw. |
11-20-2020, 06:09 PM | #3 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,436
|
Re: Best type of blade for cutting aluminum pipe
Cutting aluminum is tricky. If it gets too hot it will melt and grab the blade. Most saws like this has oil to cool the blade. Recip is good, but make sure you use good quality 16t or 14t blades. Its nearly impossible to get perfect cuts with a recip saw. There are abrasive blades made for aluminum, but the chop saw you use must run slowly as to not build up heat.
My favorite way of cutting all kinds of kinds of pipe and rod is the bandsaw. I have one that uses gravity so you set your material in the clamp vise, turn on the saw, lower the saw, walk away....when the cut is made, the saw turns off. Come back, repeat. Fine tool. |
11-20-2020, 06:52 PM | #4 |
Gone Wild
Join Date: Jul 2017
Location: Cape Coral FL
Posts: 243
|
Re: Best type of blade for cutting aluminum pipe
OK, it looks like I've once again picked another doozy of a first-time project. I will keep this advice in mind. After using a jig with a whole saw last night to try to notch the ends, I was planning to find a way to add water to cool while I cut. Is this a worthwhile endeavor or am just going to get wet while still doing it wrong?
|
11-20-2020, 08:21 PM | #5 |
Cave Dweller
Join Date: Apr 2013
Location: Always On The Move
Posts: 22,209
|
Re: Best type of blade for cutting aluminum pipe
hold it tight , fine tooth blade , dont force it and a spray bottle you will be fine .
|
11-20-2020, 09:19 PM | #6 |
Gone Wild
Join Date: Jul 2017
Location: Cape Coral FL
Posts: 243
|
Re: Best type of blade for cutting aluminum pipe
Cool, I think I found a decent band saw locally I think I'll give that and the water a try.
|
11-21-2020, 01:49 PM | #7 |
Gone Wild
Join Date: Sep 2014
Location: Orlando, FL
Posts: 1,308
|
Re: Best type of blade for cutting aluminum pipe
A rip blade will cut the aluminum pipe with ease. No need for a fine tooth or anything of the like. Its noisy as hell but cuts very well.
From 1978-1979, I worked inside the Mobile Launcher at KCS during the conversion for the Space Shuttle three exhaust holes from the Saturn single exhaust hole, making all of the required aluminum cable tray fittings from scratch for over a quarter mile of 24" cable tray installed within. I used a skill saw and rip blade for every cut made. |
04-06-2022, 06:38 AM | #8 |
Born to be Wild
Join Date: Feb 2019
Location: Palm Harbor Florida
Posts: 2,761
|
Re: Best type of blade for cutting aluminum pipe
Okay so I'm a little late posting this. I have successfully and safely cut 3/8"-1/2" thick aluminum for a boat lift on my 10" table saw using the blade pictures. It has 60 teeth and they're on a different angle than what is used on a standard wood blade. Gave me a smooth cut and I didn't have to use water. Hope this helps somebody out!
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Cutting/Copying a car type key blank into a cart key?? | Gas Yamaha | |||
Wanted: Ehaust Pipe/Header Pipe For 1990 EZGO 2 Stroke | Golf Carts and Parts | |||
G-1 starter Gen. fan blade measurement? | Gas Yamaha | |||
I need a Sawzall blade sponsor! | Lifted Golf Carts | |||
snow blade for sale | Golf Carts and Parts |