Who's planning on modding their carts?

reganr · 01-22-2010, 02:13 PM

Also, our carts come with a controller that is capable of having two sets of parameters and are already set up to accept a switch.

DealMaker8378 · 01-22-2010, 02:18 PM

My understanding as well reganr, they utilize a rocker type F/R switch so sounds pretty simple once you have a wiring diagram. Seems preferable to using different speed chips and having to stop and swap each time the need arises.

krusty0001 · 01-22-2010, 02:31 PM

Quote:

Originally Posted by reganr

Controller is set for best allround use from factory, It can be cutom tuned to individual needs. Example: Where I live there are no hills, so I may want less torque for climbing and more topend speed. Everything is a compromise, to gain here, you have to give there.

Soon as the cart gets here, I'm ready....

reganr · 01-22-2010, 02:47 PM

I 'll probebly be begging to rent the cable from you if it works (shipping both ways on me of course), others have had problems with the jumper wiring. The controller manual doesn't look too complicated, but we still need the gear ratio of the individual cart (are lifted and stock the same) and the motor specs to know the adjustment limits of some parameters.

DealMaker8378 · 01-22-2010, 02:55 PM

krusty....once you get a chance to test it, you will post a wiring schematic right?

Quote:

Originally Posted by krusty0001

Soon as the cart gets here, I'm ready....

randyzimmer · 01-22-2010, 03:46 PM

Quote:

Originally Posted by reganr

... but we still need the gear ratio of the individual cart ...

If the info posted here:
http://www.freeelectriccar.com/shopc...asp?type=specs
is correct...

Rear Axle: Gear ratio10.25:1
Wheel & Tire: 10x7 Aluminum wheel & 205/50-10 4PR

krusty0001 · 01-22-2010, 03:56 PM

Anybody here can borrow the cable, no problem. It was fairly easy to make. I wish I could test it first. I'm not even sure if I have the right connectors. It's pinned out according to the Curtis Controller Thread.

The guy from zenn30 emailed me back. He used the 1268 manual as reference for his GE Controller. He doesn't own a 1268 controller therefore didn't know what exactly what parameters to change. He did think the cart was capable of much higher speeds given our specs. (he took his Zenn from 25mph to 65mph with lots of mods)

BlackCobra · 01-22-2010, 03:57 PM

Quote:

Originally Posted by krusty0001

He did think the cart was capable of much higher speeds given our specs. (he took his Zenn from 25mph to 65mph with lots of mods)

YellowSled · 01-22-2010, 04:01 PM

Holy sh I t! 65mph in a cart! Lolz

krusty0001 · 01-22-2010, 04:42 PM

One more pic. I'm fairly certain I have the right connectors. If the pinout is correct, we should be good to go. I'll add some disconnects just in case

01-22-2010, 02:13 PM	#11
reganr Getting Wild Join Date: Oct 2009 Location: Louisiana Posts: 79	Re: Who's planning on modding their carts? Also, our carts come with a controller that is capable of having two sets of parameters and are already set up to accept a switch.

01-22-2010, 02:18 PM	#12
DealMaker8378 Getting Wild Join Date: Jan 2010 Location: Orange County, CA & Lake Havasu City, AZ Posts: 89	Re: Who's planning on modding their carts? My understanding as well reganr, they utilize a rocker type F/R switch so sounds pretty simple once you have a wiring diagram. Seems preferable to using different speed chips and having to stop and swap each time the need arises.

01-22-2010, 02:47 PM	#14
reganr Getting Wild Join Date: Oct 2009 Location: Louisiana Posts: 79	Re: Who's planning on modding their carts? I 'll probebly be begging to rent the cable from you if it works (shipping both ways on me of course), others have had problems with the jumper wiring. The controller manual doesn't look too complicated, but we still need the gear ratio of the individual cart (are lifted and stock the same) and the motor specs to know the adjustment limits of some parameters.

01-22-2010, 03:56 PM	#17
krusty0001 ****** Join Date: Dec 2009 Location: Austin Tx Posts: 72	Re: Who's planning on modding their carts? Anybody here can borrow the cable, no problem. It was fairly easy to make. I wish I could test it first. I'm not even sure if I have the right connectors. It's pinned out according to the Curtis Controller Thread. The guy from zenn30 emailed me back. He used the 1268 manual as reference for his GE Controller. He doesn't own a 1268 controller therefore didn't know what exactly what parameters to change. He did think the cart was capable of much higher speeds given our specs. (he took his Zenn from 25mph to 65mph with lots of mods)

01-22-2010, 04:01 PM	#19
YellowSled Gone Wild Join Date: Jan 2010 Location: Westminster, MD Posts: 239	Re: Who's planning on modding their carts? Holy sh I t! 65mph in a cart! Lolz

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
two of my carts!	Gas Yamaha
ac carts	Electric golf carts
Carts, carts, carts!!!-'01 EZ GO-$1300.00!!??	Golf Carts and Parts