07-23-2017, 01:51 PM | #21 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: Clone kill relay wiring diagram
If I pull my relay out of the plug, it idles and no way to shut it off. So I could put in a switch to disable the relay in the pedal wire or ground to it, and then it would keep running. I really have no need for it so I did not. The one need is if I have to pull start it then I can't run the pedal, so then I can unplug the relay, which is right next to the recoil. I've done it just to make sure it starts that way lol. It started pretty easily.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-12-2020, 07:55 PM | #22 |
Not Yet Wild
Join Date: Sep 2020
Posts: 13
|
Re: Clone kill relay wiring diagram
Digging out this old, but extremely useful thread.
If my goal is to use pedal start/stop and the Ezgo Starter/Gen, what wires do I need from the original Predator 420 harness? I know I need the coil wire to ground from the relay to kill it. I'm trying to decide if I need any other wires. Can I unplug my Predator factory key switch assembly and remove it altogether? Thanks for the great info. I'm very close to finishing my '95 Ezgo Predator swap. |
11-15-2020, 07:11 AM | #23 |
Not Yet Wild
Join Date: Sep 2020
Posts: 13
|
Re: Clone kill relay wiring diagram
The answer:
If you are using the Pedal kill wire and factory Ezgo starter/generator, none of the wires are required from the stock Predator Key switch. |
06-24-2023, 07:29 PM | #24 |
Not Yet Wild
Join Date: Jun 2023
Posts: 50
|
Re: Clone kill relay wiring diagram
Almost ready to crank my new 459 in my G2. Just a bit concerned that I have the relay hooked to the correct wire on the predator 459. The kill wire comes from the ignition coil on the very top of the engine, correct? The other wires are the yellow oil shut of line which leads to a small black box where a black wire also goes into, then black wire out. To me this would make sense to be the kill wire. But everything I read and can find says it should lead from the top of the engine. Anyone know? I'm reusing the oem starter/generator and the 5 pin relay way to kill the engine.
|
06-24-2023, 07:59 PM | #25 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,642
|
Re: Clone kill relay wiring diagram
Just bypass the box all together and extend the black wire to the relay. The box merges the low oil sensor with the kill wire. The motions of a golf cart can trigger the low oil sensor causing the engine to cut. BUT do check your oil regularly
|
06-24-2023, 10:16 PM | #26 |
Not Yet Wild
Join Date: Jun 2023
Posts: 50
|
Re: Clone kill relay wiring diagram
Thank you for all your help on this. So I got it running but it wouldn't shut off when letting go of gas pedal. This was with the relay attached to the wire coming on top of the motor. Now maybe my attachment to that wire wasn't good or as you say I had the wrong wire. Are you 100% sure that the black wire attached to the yellow wire is the kill wire on the 459? Just throws me off cause every other predator motor the kill wire comes from the same place the wire I have on the top does. And that black wire coming from the box with the yell wire has a red circle at the end. The manual says nothing about these wires.
|
06-24-2023, 10:40 PM | #27 |
Not Yet Wild
Join Date: Jun 2023
Posts: 50
|
Re: Clone kill relay wiring diagram
This is really all I can find. And when watching this video it looks like the kill wire is the top wire. And that the charge coil is the brown wire coming out back of the block.
|
06-24-2023, 11:27 PM | #28 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,642
|
Re: Clone kill relay wiring diagram
A simple test would be to just touch the black wire to the block with the engine running. A sure way to test if it is the kill.
|
06-25-2023, 12:04 PM | #29 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,176
|
Re: Clone kill relay wiring diagram
The wire coming from the side of the coil is the kill wire. Find the wire coming from the white assembly next to the crank and it should go to the little box. Wire coming from that is the charging output.
|
06-25-2023, 02:18 PM | #30 |
Not Yet Wild
Join Date: Jun 2023
Posts: 50
|
Re: Clone kill relay wiring diagram
I just confirmed it is the black wire coming from the top. When engine is running and this wire is grounded to the block the engine dies. However, if I attach it to my 5 pin relay I wired the engine will not start. So I'm assuming that the wire I attached the positive pedal switch must not have a good connection. I'm getting there but slowly
|
Tags |
clone, kill, relay, wiring |
|
|
Similar Threads | ||||
Thread | Forum | |||
clone engine relay? | Clone Engine Swaps | |||
88 CC DS Clone swap: the kill wire | Clone Engine Swaps | |||
Clone kill switch | Clone Engine Swaps | |||
relay wiring to kill clone | Clone Engine Swaps | |||
clone wiring diagram? | Big Block Talk! |