|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
03-28-2018, 10:00 AM | #1 |
Not Yet Wild
Join Date: Jul 2017
Location: KC
Posts: 43
|
Key Switch - Signal Wire Question
So I just got done hooking up a voltage reducer, headlights, turn signals, etc… All went well enough. Last night I finished up and hooked up the battery pack back up. When I hooked up the voltage reducer to the pack I had some exciting sparks; at first I figured it were capacitors or whatever this first time but then quickly realized everything worked! This is bad because the key was off. I unhooked the key signal wire for the voltage regulator and left everything else. Accessories are off. I touch to the positive terminal, Accessories turn on. So it is my key wiring, specifically my volt meter was providing power to the signal wire.
So it is a 90 36v ds resistor cart. The key switch wiring goes: Pack negative has a white wire going to the charging port. From that same post I have a thin red wire going to one side of the switch. So this is the negative side. From the other side of the switch I have thing blue wire going to the F&R micro switch. The other side of that switch is yellow to the solenoid. The other side of the solenoid is green to the vglide. So in theory the key only gets positive when the cart is in Forward or Reverse? When I hooked up the volt meter I ran a hot wire to the volt meter, than took the negative to the blue wire on the switch. I feel like I could just put the signal wire for the volt reducer to the other side of the key switch and all will be well. But after looking at this last night it seems wrong and i probably should have a positive wired to another positive. Is there some way to get positive out of the key switch without being in F/R? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-28-2018, 01:11 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Key Switch - Signal Wire Question
If I read this correctly you have one of the rare carts with negative current through the key switch. This keyswitch never sees (+). The reducer on/off trigger wire must connect to positive, not negative.
In this case there are 2 alternatives. Provide a separate toggle switched 36v positive for the trigger wire connection. Install a switch relay which can use the (-) from your keyswitch to complete a (+) connection to the trigger wire. |
03-28-2018, 01:18 PM | #3 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Key Switch - Signal Wire Question
In addition to what Scottyb said, You must also have the micro-switch in the VGlide mis-wired or by-passed since the only way to get the positive voltage through the Solenoid coil to trigger the converter when the key switch was OFF is if the Pedal was pressed.
|
03-28-2018, 03:51 PM | #4 | |
Not Yet Wild
Join Date: Jul 2017
Location: KC
Posts: 43
|
Re: Key Switch - Signal Wire Question
Quote:
sigh. So for a voltage reducer signal wire and a volt meter.... do you think i would need to have a switch or relay designated for 36 volts or would the amperage be so low it not really matter? Because i think i have a light wiring harness that has a 40amp 12 volt relay, and tons of 12 volt switches from over the years. |
|
03-28-2018, 03:54 PM | #5 | |
Not Yet Wild
Join Date: Jul 2017
Location: KC
Posts: 43
|
Re: Key Switch - Signal Wire Question
Quote:
After last night i now realize why i had so many problems with wiring that. |
|
03-28-2018, 04:10 PM | #6 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Key Switch - Signal Wire Question
It is probably easier to re-wire the cart for a positive key switch.
Disconnect the 2 wires from the key switch and splice them together. You can now wire any accessories: Voltmeter or Converter to your new positive key switch. Use different color wires (or tape the ends of the wires with different colored tape) for easy identification. Use the diagram below for reference: |
03-28-2018, 05:30 PM | #7 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Key Switch - Signal Wire Question
LOL
|
03-28-2018, 08:19 PM | #8 | |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: Key Switch - Signal Wire Question
Quote:
Sergio, I swear, one day you are going to tell us you retired as the Club Car Design Engineer or Electrical Engineer, as there is just no way you can know all you do and not be plugged into them (Club Car) in some way.... I do not want to make your head swell, but I am a better trouble shooter and have a better understanding of many things from your writings and recommendations... No one ever says those 2 little words as often as they should, but "Thank You" for what you do and share with all the rest of us... |
|
03-29-2018, 02:58 PM | #9 |
Gone Wild
Join Date: Nov 2014
Location: New Albany, Indiana
Posts: 566
|
Re: Key Switch - Signal Wire Question
|
03-30-2018, 07:16 AM | #10 |
Gone Wild
Join Date: Jan 2017
Location: Queensland Australia
Posts: 1,332
|
Re: Key Switch - Signal Wire Question
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Question on running wire from key switch to voltage reducer | Electric EZGO | |||
2004 club golf cart key switch question? Can I wire both wires to one lug on key swit | Electric Club Car | |||
help with turn signal wire problems | Electric Club Car | |||
Turn signal wire cover? | Gas Yamaha | |||
7 wire turn signal / flasher question | Gas EZGO |