01-06-2022, 06:31 PM | #41 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
Got the case back together. Also began some valve lapping
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
01-07-2022, 08:06 PM | #42 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
3 lapping tries until we held water and compressed air bubbles didn't come through
|
01-08-2022, 01:25 PM | #43 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
Some more progress today. Got the valves sealed well and lash set per specs. Plastics on for the most part. I am at a stopping waiting on more parts. Hope to get some hardware tomorrow but the primary needs new rollers along with a new slinner sheave for the secondary.
|
01-09-2022, 03:47 PM | #44 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
Got the cradle on today. Working on the next round of parts ordering.
|
01-10-2022, 07:39 AM | #45 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,010
|
Re: Camp Project "Got Milk"
Lookin good
|
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
01-23-2022, 05:52 PM | #46 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
Got the new billet rollers ordered. Commenced dis-assembly and inspection of primary.
1 current roller is worn a little over 1/16 - inch down. It also looks like I am missing a small nylon bumper. Not sure if this is obtainable? Also what type of grease should I use on the ramp pivots when I take them apart and re-assemble? |
01-29-2022, 03:50 PM | #47 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
Got the primary rollers replaced and greased. Also got the crappy eBay carb cleaned and back on. Mix screw set to 2 revolutions out from bottom.
Gonna guess dirt ingestion was the demise of this engine previously. The intake was just horrid. |
02-18-2022, 08:29 PM | #48 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,010
|
Re: Camp Project "Got Milk"
Progress??
|
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
02-18-2022, 09:21 PM | #49 |
Runs with scissors-
Join Date: Dec 2010
Location: Da UP
Posts: 1,962
|
Re: Camp Project "Got Milk"
X2. Hope all is well! Be good to hear how it’s goin’
|
02-19-2022, 07:55 AM | #50 |
Not Yet Wild
Join Date: May 2021
Location: Upstate, NY
Posts: 70
|
Re: Camp Project "Got Milk"
Al,
Its still, but currently at a standstill. The engine is awaiting to be re-installed in the G16, but the weather has not been cooperative! We're talking highs in the 20's and lows below zero! We had 1 day of almost 50 degrees but is was a work day.... Ended up picking up another project (05 GMC Yukon XL) for a family trip to TN that will be taking up my time this weekend. Hopefully over the next few weeks weather will at least get above 32 and I will be back out in the shed! |
Tags |
g16, g16a, yamaha |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
My first FULL "Sparky" Project ... Some help definitely needed | Electric EZGO | |||
'99 TXT "Face Lift" Winter Project Completed... | Electric EZGO | |||
project "KEEPIN IT CLASSY" yamaha g1 build | Members Rides | |||
1998 Club Car project "Salt Shaker" | Members Rides |