|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
02-28-2009, 11:45 AM | #1 |
Not Yet Wild
Join Date: Feb 2009
Posts: 12
|
help identifying cart
if someone can help id a cart thank you in advance
serial#613770 manufacture code k1590 and also i need directions to a schematic for the forward reverse switch as it is disconnected. i am new to carts so bear with me. thank you |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-28-2009, 01:56 PM | #2 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: help identifying cart
Born in May 15, 1990.
Look in the stickies for schematics. |
02-28-2009, 04:34 PM | #3 |
Not Yet Wild
Join Date: Feb 2009
Posts: 12
|
Re: help identifying cart
thanks a ton found them
|
02-28-2009, 08:05 PM | #4 |
Not Yet Wild
Join Date: Feb 2009
Posts: 12
|
Re: help identifying cart
i need a little more help i believe i need a new controller as the solenoid just clicks and all circuits and switches check out. i do not know what controller i need i know it is a curtis but there are a few different ones amperage wise.also i need schooling on the slang like what is pds non pds. dcm etc.
|
02-28-2009, 08:22 PM | #5 |
Not Yet Wild
Join Date: Feb 2009
Location: Around Houston ,Tx.
Posts: 54
|
Re: help identifying cart
Check across the solenoid and make sure it is closing. I had one that drove me crazy because it clicked but was not making. If you don't have a meter to check it, you can jack up the rearend, put it in foward or reverse and jumper across the big leads on the solenoid and see if it will go. Solenoids are cheaper than controllers.
|
02-28-2009, 08:28 PM | #6 |
Not Yet Wild
Join Date: Feb 2009
Posts: 12
|
Re: help identifying cart
yea ive been researching all day already jumped solenoid with the switch in forward and pushed the pedal still no go. thanks for the input though.
|
02-28-2009, 09:04 PM | #7 |
Golf Cart Photographer
Join Date: Jan 2007
Location: Wichita Falls Texas - My Ride 2010 Club Car
Posts: 6,236
|
Re: help identifying cart
Hello brodg and Welcome to the forum.
|
02-28-2009, 09:13 PM | #8 | |
steeplejack x
Join Date: Jan 2007
Location: Republic of Texas
Posts: 3,382
|
Re: help identifying cart
Quote:
Non PDS/DCS = Fleet = series wound PDS = "Precision Drive System" = EZGO 2nd gen regenerative drive system. Shunt wound. DCS = "Drive Control System" = EZGO 1st gen regenerative drive system. Shunt wound. Good luck. HIH |
|
03-01-2009, 07:03 AM | #9 |
Not Yet Wild
Join Date: Feb 2009
Posts: 12
|
Re: help identifying cart
thank you pggroves how do i tell what i have pds non pds or fleet.also i found a 350a 36v controller on ebay will this work or do i need to find a 250a one.and is there anywhere i can get a tree chart to diagnose it properly. and hello back to everyone one more thing when i jumped the solenoid i accidentally burnt the leg on the solenoid diode is this something important or can i get away without it while i work on the cart i went to ratshack and got a 200piv 3a diode will this work. it's all they had
|
03-01-2009, 09:33 AM | #10 |
doin it in the desert
Join Date: Dec 2008
Location: Sonora Desert,Az
Posts: 5,603
|
Re: help identifying cart
welcome to BGW.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
EZ GO Identifying the problem with GO | Electric EZGO | |||
Help Identifying Motor | Gas Yamaha | |||
Help in identifying and troubleshooting hesitation | Electric Club Car |