03-12-2013, 11:01 PM | #21 | |
Not Yet Wild
Join Date: Dec 2012
Location: Linwood, KS
Posts: 1
|
Re: Rear end strength
I am beginning almost the same build...i have a kz600 ninja motor i am slapping in a mid 80's ezgo....this should be fun....i will make a thread with pictures as i get going. I just have the motor and rear plastic off now.....but will hit it hard as soon as i get my wiring harness in to fire the motor....making sure the motor is good first.
Quote:
|
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-18-2013, 04:30 PM | #22 |
Gone Wild
Join Date: Jun 2012
Location: Callahan,Florida
Posts: 337
|
Re: Rear end strength
|
03-27-2013, 01:14 PM | #23 |
Gone Wild
Join Date: Sep 2012
Location: bikini state
Posts: 2,715
|
Re: Rear end strength
not sure if this helps ya tonka,but the me29 first few yrs of ezgo for/rev axles have 1-1/8th axles shafts in the long stretched part of the shaft
.930 on the outter bearing spline area just found out mine has lasted 20 yrs and looked great till it sat and flash rust,,then i drove it and didnt no bout the rust and now replacing everything..with a detailed thread with part numbers for everything its gettin a lincoln locker while out also..why?,because i drive over stuff |
03-27-2013, 07:01 PM | #24 | |
Smoov az a gravy sammich
Join Date: Oct 2008
Location: Limestone, Illinois
Posts: 3,462
|
Re: Rear end strength
Quote:
You built a rear end sassy? |
|
03-27-2013, 07:34 PM | #25 |
Gone Wild
Join Date: Sep 2012
Location: bikini state
Posts: 2,715
|
Re: Rear end strength
totally replacing all bearing in the rear axle,8 total in a older me29 transaxle.
heres all the part numbers for everything in here http://www.buggiesgonewild.com/gas-e...questions.html doing it in my build thread in my sig get bearings and seals tomorrow.. |
03-27-2013, 07:37 PM | #26 |
Smoov az a gravy sammich
Join Date: Oct 2008
Location: Limestone, Illinois
Posts: 3,462
|
Re: Rear end strength
Thanks for the info Sassy!
|
03-28-2013, 09:02 AM | #27 |
Gone Wild
Join Date: Sep 2012
Location: bikini state
Posts: 2,715
|
Re: Rear end strength
anyone thats been in a ezgo rear end case no what this could be..was broken in the bottom of the case when tore down..wold like to no if its part of the gov or what before i put this all back together..? thanks
|
03-28-2013, 09:24 AM | #28 |
Gone Wild
Join Date: Dec 2012
Location: The Villages, FL
Posts: 552
|
Re: Rear end strength
Part of a jigsaw puzzle of the Blue Ridge mountains, during the fall?
Sorry. |
09-15-2013, 07:24 PM | #29 |
Gone Wild
Join Date: Sep 2011
Location: O'Fallon IL....for now....
Posts: 192
|
Re: Rear end strength
Hey there crf714, I'm doing a 2005 636cc engine swap myself. Is there a way to contact you just to chat about what you've done so far?
If you would, email me with a good number and a time to contact you. cb632@peaknet.net Thanks a ton, Clint |
02-02-2022, 04:17 AM | #30 |
Not Yet Wild
Join Date: Jun 2021
Posts: 14
|
Re: Rear end strength
I know this was a very lonGB time ago but how long did it last
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Strength of dana rear? | Electric EZGO | |||
1986 carryall II rear end strength? | Gas Club Car | |||
driven clutch and belt strength? | Big Block Talk! | |||
04 ezgo rear end strength | Big Block Talk! |