07-04-2018, 05:49 PM | #1 |
Not Yet Wild
Join Date: Sep 2014
Location: SW Indiana
Posts: 48
|
Clone 420 to replace Robin 295
The question::: replacing the junked out 295 in 93 EZGO with stock parts using 18-850-8 tires using VC kit for 420 HF . 420 having 3600 rpm, about how much mph is (area of) usual ????
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-04-2018, 07:54 PM | #2 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Clone 420 to replace Robin 295
Most carts if you turn the governor all the way up and hit 4K rpm that is usually 16-20mph. If you put a clone in it will go the same speed....unless you get HD springs for it that are about $20 and use a free flow muffler of some kind you might get 4mph more or so with no governor. You can do a lot of other mods too, but HS gears will add about 10mph and with a clone it will have no problem getting up to speed. Then you would run around 30mph give or take. Many carts will fit 20 inch lawn or road tires, anything not atv style, and give you a bit more than 18 tires. I put HS gears in a CC and ran 28 on gps hitting the rev limiter, all stock other than me turning up the governor. I forget but think it did 19 before the gears.
|
07-04-2018, 09:12 PM | #3 |
Not Yet Wild
Join Date: Sep 2014
Location: SW Indiana
Posts: 48
|
Re: Clone 420 to replace Robin 295
Thank You SHO, I have no idea what this would in stock form,, I unhooked all governor cables and run straight to carb trying to get some speed..,6 mph on gps before rev limiter hit,, decided on BB
|
07-05-2018, 08:12 AM | #4 |
Not Yet Wild
Join Date: Sep 2014
Location: SW Indiana
Posts: 48
|
Re: Clone 420 to replace Robin 295
Will weak valve springs do this no power crap??
|
07-05-2018, 09:57 AM | #5 |
Crazy Ole Man
Join Date: Jan 2016
Location: Owego NY
Posts: 2,758
|
Re: Clone 420 to replace Robin 295
It will rev out 42-4500 rpm and the stock valves will start to float. At this point if you run it hard there comes the possibility of dropping a valve. It's just the way there built.
|
07-05-2018, 04:53 PM | #6 |
Not Yet Wild
Join Date: Sep 2014
Location: SW Indiana
Posts: 48
|
Re: Clone 420 to replace Robin 295
I have messed enough with this,, VC has shipped the clone install kit,,LTR
kit |
07-05-2018, 07:47 PM | #7 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Clone 420 to replace Robin 295
6mph I would guess a major engine issue or the clutch is not shifting. But '93 it could be that tired you know. Mine needed a rebuild and I put a clone in, its cheaper and more power.
|
07-06-2018, 08:14 AM | #8 |
Not Yet Wild
Join Date: Sep 2014
Location: SW Indiana
Posts: 48
|
Re: Clone 420 to replace Robin 295
I noticed i could push valve spring down with little effort
|
07-06-2018, 06:10 PM | #9 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Clone 420 to replace Robin 295
I took the stock clone springs off by hand, getting the HD ones on was a little harder.
|
08-04-2018, 06:49 PM | #10 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Clone 420 to replace Robin 295
It might be that tired, most all carts are about 9hp stock some newer ones up to 12 range. If you ever ran a 10hp lawnmower you know what you have just higher gearing at speed. Stock carts usually go 12mph, without governor 18-20 maybe it depends, a G1 would go near 30 because that 2 stroke would rev but most 4 strokes are similar they all have near same gearing and rpm range. Most run 4-4500 rpm no governor about 11:1 overall gearing with an 18 tire you can put it in a gearing calc and it will tell you.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Replace 1 or all | Electric Club Car | |||
2002 workhorse, rebuild robin or swap a clone? | Gas EZGO | |||
exhaust 2pg replace | Gas EZGO | |||
What Carb to replace stock clone | Clone Engine Swaps | |||
Can a 350 replace a 295? | Gas EZGO |