|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
09-24-2021, 03:19 PM | #1 |
Not Yet Wild
Join Date: Sep 2021
Posts: 9
|
2003 G22E Motor Cap Re-Attachment
I have a 2003 G22E. I am an idiot and removed the two screws near the speed sensor that I now know secure the bearing retainer. In order to fix that issue I need to remove the motor end cap. I removed the four long bolts that secure the end cap but had to pull quite a bit to separate the cap from the motor. I pulled so much that the motor cylinder came out too.
My issue now is lining everything up to get the four bolts secured again. The bolt passed through a small eye hole in the motor and then into a threaded cavity at the far side. Any tips on how do get this all lined up correctly? A video would also be awesome if anybody know of one. I am a newbie but would really like to do this. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-24-2021, 03:34 PM | #2 |
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,125
|
Re: 2003 G22E Motor Cap Re-Attachment
You need to install the armature in the end cap with brushes before you slide on the outer case. (at least that is how my motor is built (G29 though). I hope you have the motor removed from the cart.
|
09-24-2021, 04:22 PM | #3 |
Not Yet Wild
Join Date: Sep 2021
Posts: 9
|
Re: 2003 G22E Motor Cap Re-Attachment
Any good videos on how to install the armature with brushes? I am searching now.
|
09-24-2021, 04:41 PM | #4 |
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,125
|
Re: 2003 G22E Motor Cap Re-Attachment
I never saw any but I was able to do it quite easily. Not sure how different your G22E motors are though. Most motors are very similar in construction though.
|
09-27-2021, 10:26 AM | #5 |
Gone Wild
Join Date: Nov 2013
Location: Western NY
Posts: 631
|
Re: 2003 G22E Motor Cap Re-Attachment
For the bearing plate - Use a small pick to rotate the plate in to position. You can easily see when the holes are lined up. Now get a longer screw of the same thread size. Screw the longer screw in by a few threads and use it to pull the plate up. Hold the plate in position and install one of the factory screws in the other hole. Remove the longer screw and install the remaining factory screw.
For the armature - Push the motor brushes far enough in to the brush holders to actually disengage the springs. Insert the armature in to the end cap and push the brushes back in to position. Make sure that brush springs are now engaged. Slide the stator assembly over the armature and line up and reinstall the 4 bolts. |
09-27-2021, 02:54 PM | #6 | |
Not Yet Wild
Join Date: Sep 2021
Posts: 9
|
Re: 2003 G22E Motor Cap Re-Attachment
Quote:
|
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
2003 g22e not running - leaking oil at the motor? | Electric Yamaha | |||
Should I buy this 2003 G22e $720 | Electric Yamaha | |||
2003 G22E Will not Run with Charged Batteries | Electric Yamaha | |||
2003 G22e tie rod question | Electric Yamaha | |||
2003 G22E, programmable controller? | Electric Yamaha |