|
Extreme DC! Extreme Electric Golf Carts! |
|
Thread Tools | Display Modes |
08-13-2019, 02:26 PM | #1 |
Gone Wild
Join Date: Aug 2018
Location: Orange County, California
Posts: 279
|
What to look for when buying parts for a LEAF LI conversion?
I am looking for some advice into what all I should be looking into and possibly some questions I should be asking when searching out parts for a LEAF LI conversion. I have a 2007 Columbia ParCar with 500 amp Alltrax Controller.
Looking to go with the 14 module setup similar to what MCJEFE did in his "DIY 101 - 14 cell Nissan Leaf lithium pack" Questions that I have at first is: Is there much difference in purchasing Gen 1 or Gen 2 modules? Is Gen 2 that much better than Gen 1? I am also confused when I look at sites like TechDirect and they have modules with different Kwh ratings. Why is this? (i.e. Nissan Leaf Battery G2 Module Lithium Ion 14 kWh 500 watt per module Lot of 28; Nissan Leaf Battery G2 Module Lithium Ion 14 kWh 500 watt per module Lot of 16. ...) Thanks in advance for your help and support on this. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-14-2019, 06:50 AM | #2 | |
Gone Wild
Join Date: Jul 2018
Location: Central Ohio
Posts: 1,720
|
Re: What to look for when buying parts for a LEAF LI conversion?
Quote:
There are a number of BMSs to choose from. I went with a ZEVA because there are others on here who have shared their builds with it and were able to offer experienced advice. There are also some folks recently that have been installing Chargery BMSs. I have a build thread on here, but it jumps around between lithium, gas to electric swap, rebuild and aftermarket upgrades. It gets confusing if you are just looking for specific information. Hope this helps. I'll answer any questions I can. I'm sure the gurus will be along soon to add information. |
|
08-16-2019, 12:00 PM | #3 | |
Gone Wild
Join Date: Jan 2013
Location: Saint Petersburg, FL
Posts: 2,089
|
Re: What to look for when buying parts for a LEAF LI conversion?
Quote:
Lithium does degrade *very slowly* over time with proper use. If abused, it can degrade quickly. So if you don't know the capacity of the battery then it's a crap-shoot. |
|
08-17-2019, 12:50 PM | #4 |
Gone Wild
Join Date: Aug 2018
Location: Orange County, California
Posts: 279
|
Re: What to look for when buying parts for a LEAF LI conversion?
Thanks guys. I appreciate the input.
I have found a couple more threads after posting this that has also shed some light on this. Just like many on here, just trying to get as much info I can before spending money. I am still getting my cart up and running. It is a work in progress that I finally got home so I can spend some time with it. Changing it from a stock Columbia ParCar Eagle with a bad controller to a completely rewired (like the Club Car IQ) ParCar with 400amp Contactor, Alltrax XCT48500-IQ. Getting stumped by a few things, but trying to work through it. Sent from my SM-G930T using Tapatalk |
08-18-2019, 07:33 AM | #5 |
Gone Wild
Join Date: Jul 2018
Location: Central Ohio
Posts: 1,720
|
Re: What to look for when buying parts for a LEAF LI conversion?
Your basically doing what I did. I swapped out the gas drive line to a 2003 DS IQ wiring harness and the rest you can see in my siggy. Let me know if you have any questions, I'll help where I can.
|
08-19-2019, 12:08 PM | #6 |
Gone Wild
Join Date: Aug 2018
Location: Orange County, California
Posts: 279
|
Re: What to look for when buying parts for a LEAF LI conversion?
I was working on it on Saturday and noticed that had a bad micro switch for the 'Foot Switch' on my throttle. went down and got a replacement for that. Now I think the coil on my main contactor is bad. A week ago I was hearing it click on and off, but now i get nothing from it. I pulled it off to test it on my workbench, attempted to hook it up to a 12v test battery, and it blew my diode (all over the workbench).
Does anyone have any suggestions on how I can go about testing this contacor and coil to see if it truly is bad before dropping more $$ on something that is still good? |
08-19-2019, 12:30 PM | #7 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: What to look for when buying parts for a LEAF LI conversion?
The diode would have exploded if you applied the negative power lead to the side with the band (cathode).
What is the resistance of the Solenoid coil? Are the little contacts on the bottom of the Solenoid making contact prior to applying power? You may need close to 36v to make the solenoid engage but the coil resistance will help determine if the Solenoid is good. |
08-19-2019, 02:24 PM | #8 | |
Gone Wild
Join Date: Aug 2018
Location: Orange County, California
Posts: 279
|
Re: What to look for when buying parts for a LEAF LI conversion?
Quote:
Resistance is about 17.1 ohms. Yes ... the contacts on bottom of the solenoid are making contact. When i press down on the contactor, they do separate. Does this sound correct? I may have to try it with 36v if everything sounds right. I am a RV technician (at least last couple of years), so finding the extra batteries (at least for testing) is not hard to do. I did bring it in to work with me to test and ask questions with some of my fellow techs up here with more electrical experience than I have. |
|
08-19-2019, 03:21 PM | #9 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: What to look for when buying parts for a LEAF LI conversion?
That first coil on the Solenoid pulls pretty hard and that is why the low resistance.
If You separate the small contacts on the bottom of the Solenoid, the resistance should increase as the second coil gets inline and provides the lower current needed to keep the main contacts closed. |
08-19-2019, 03:23 PM | #10 |
Gone Wild
Join Date: Aug 2018
Location: Orange County, California
Posts: 279
|
Re: What to look for when buying parts for a LEAF LI conversion?
Well .... the Solenoid tested out good. I guess 12v just wasn't enough to pull the contactor in. I tried it with 36v and it sucked it in just like it was supposed to.
Now just replace the diode and try it on the cart again. |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Lithium Conversion (leaf battery) | Lithium EZGO | |||
leaf mondules conversion issues | Lithium Club Car | |||
Lithium Nissan Leaf conversion x 2 | Lithium Club Car | |||
Leaf conversion EZ-GO Txt | All things Lithium | |||
Buying used parts | Electric Club Car |