01-03-2023, 05:44 PM | #1 |
Not Yet Wild
Join Date: Oct 2022
Location: Athabasca, AB
Posts: 24
|
Primary drive sleeve
Hi folks,
Anyone happen to know the outer diameter for the needle bearing sleeve on the primary drive? I found the bearing & seals i need, but i need to build a sleeve. Thanks in advance. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
01-05-2023, 09:25 PM | #2 |
Gone Wild
Join Date: Jan 2018
Location: Indy
Posts: 166
|
Re: Primary drive sleeve
|
01-06-2023, 10:28 PM | #3 |
Gone Wild
Join Date: Mar 2022
Location: Ohio
Posts: 455
|
Re: Primary drive sleeve
Inch and a 1/2 been a minute since I had my cart apart so don’t quote me sorry
|
01-08-2023, 02:07 PM | #4 |
Not Yet Wild
Join Date: Oct 2022
Location: Athabasca, AB
Posts: 24
|
Re: Primary drive sleeve
|
01-09-2023, 12:11 PM | #5 |
Not Yet Wild
Join Date: Oct 2022
Location: Athabasca, AB
Posts: 24
|
Re: Primary drive sleeve
So here is the info i’ve been able to find.
In the 1963-80 gas manual: Sec 4 pg 4, figure 4b-43. #20a needle bearing, late 64( looking for the sleeve on the outside) In the 1963-81 gs parts book i have: Page 9, part 29 in pic, Part#’s are: 36462-64 needle bearing sleeve assembly (64 to 66) 36462-67 (67 to present) If i could find just the outside sleeve dimensions or drawing i could build my own. |
01-09-2023, 04:29 PM | #6 | |
Gone Wild
Join Date: Jan 2018
Location: Indy
Posts: 166
|
Re: Primary drive sleeve
Quote:
.78" L 1.5" OD 1.368 ID (difficult for me to measure, so your bearing OD should dictate) In case you don't have an old one, I'll note that this sleeve captures the bearing between two oil seals. Good Luck! |
|
01-09-2023, 05:01 PM | #7 | |
Not Yet Wild
Join Date: Oct 2022
Location: Athabasca, AB
Posts: 24
|
Re: Primary drive sleeve
Quote:
Looks like the seals are backwards to what i usually see on other things. Wasn’t sure which way they went in. Thanks again. Here is what i was able to find for bearings & seals according to the inner race i had. Seal: National brand pt# 340815 Bearing: BA188Z |
|
01-09-2023, 06:21 PM | #8 | |
Gone Wild
Join Date: Jan 2018
Location: Indy
Posts: 166
|
Re: Primary drive sleeve
Quote:
The seal on the opposite side is ALSO inserted opposite, so both seals face in the same direction. |
|
01-09-2023, 07:28 PM | #9 |
Not Yet Wild
Join Date: Oct 2022
Location: Athabasca, AB
Posts: 24
|
Re: Primary drive sleeve
|
01-10-2023, 10:42 AM | #10 |
Not Yet Wild
Join Date: Oct 2022
Location: Athabasca, AB
Posts: 24
|
Re: Primary drive sleeve
Update: was measuring up parts last night, i found i have to change sleeve dimensions to a different size.
New outer sleeve size with seals i was able to find: 1.00” wide 1.368” I.D. 1.55” O.D. same diameter as Primary Floating sleeve (one with felt). 340815 seal is 1.5” 1.03” Original primary inner sleeve Once i build one i’ll post a pic. |
|
|
Similar Threads | ||||
Thread | Forum | |||
primary drive or belt | Gas Columbia ParCar | |||
92 Primary Drive Clutch | Gas Columbia ParCar | |||
92 Par Car Primary Drive removal | Gas Columbia ParCar | |||
g16 primary drive clutch | Gas Yamaha | |||
removing the primary drive | Gas Columbia ParCar |