|
|
|||||||
| Big Block Talk! Everything about swapping a big block engine into your cart! |
  |
|
|
Thread Tools | Display Modes |
08-06-2008, 08:49 AM
|
#1 |
|
Admin/Moderator
 Join Date: Dec 2006
Location: Ohio
Posts: 18,135
|
B&S engine info
Thanks Shawn M.
|
|
Ron
 PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
08-06-2008, 09:19 AM
|
#2 |
|
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,899
|
Re: B&S engine info
Thanks Ron! My 20hp motor wiring diagram is on page 11
|
|
|
|
|
08-09-2008, 09:24 AM
|
#3 |
|
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,888
|
Re: B&S engine info
Thanks Shawn M. Found my problem the other day. When I "spliced" my stock harness to lengthen it......one butt connector was not crimped well and came undone. Wilson runs fine again. Dave
|
|
|
|
|
08-09-2008, 09:59 AM
|
#4 |
|
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,899
|
Re: B&S engine info
no problem
helping others should be what a forum is about. Did you remove the fuel cut off from the float bowl? I am thinking about doing this as it is supposed to help a little bit on the fuel flow. |
|
|
|
|
10-06-2008, 08:19 PM
|
#5 |
|
Getting Wild
Join Date: Sep 2008
Location: FOLEY,ALABAMA 36535
Posts: 84
|
Re: B&S engine info
would you wire your vtwin to crank, and idle?, how would you make up the throttle cale?, do they offer a special cable you can buy for upgrade?
|
|
|
|
|
10-06-2008, 09:11 PM
|
#6 |
|
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,899
|
Re: B&S engine info
i have mine set to crank and idle. read my build thread for pictures
|
|
|
|
|
02-20-2010, 09:59 PM
|
#7 |
|
Not Yet Wild
Join Date: Feb 2010
Location: Southwest of Fort Worth, TX
Posts: 23
|
Re: B&S engine info
What modifications would you have to do to fit a 25-30hp Briggs or kohler into a 2009 club car precedent. Another question is what is the max rpm of a 25-30 hp engine. I would like to know what the top speed of a 25-30hp engine would give in comparison to the 31.5 that the 11.5@3600 rpm.
|
|
|
|
|
02-20-2010, 11:06 PM
|
#8 |
|
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,899
|
Re: B&S engine info
max RPM depends on how you build it. with a rev kit and timing advance your going to see 4500 rpm. maybe even 5500.
the small blocks -23 and under like to rev more than the 25hp and up. it all depends on your wallet |
|
|
|
|
02-20-2010, 11:44 PM
|
#9 |
|
Not Yet Wild
Join Date: Feb 2010
Location: Southwest of Fort Worth, TX
Posts: 23
|
Re: B&S engine info
If you put a rev kit on it will it pose a threat to the engine turning more RPM with heat? I would be afraid of burning it up (the 11.5hp).
|
|
|
|
|
02-20-2010, 11:58 PM
|
#10 |
|
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,899
|
Re: B&S engine info
please ask your question in the forum instead of the sticky thread.
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| yamaha G-2 info | Lifted Golf Carts | |||
| Info Help on CC's | Electric Club Car | |||
| Amsoil Synthetic engine oil or Royal Purple engine oil | Big Block Talk! | |||
| Need Help with parts and other info. | Gas EZGO | |||
| Guest info | Announcements | |||
Linear Mode
