|
Big Block Talk! Everything about swapping a big block engine into your cart! |
|
Thread Tools | Display Modes |
10-29-2019, 04:39 PM | #11 |
Getting Wild
Join Date: May 2017
Posts: 87
|
Re: Ezgo vangaurd 18
I have some more pics. I'm determined not to lift this cart.i am going to put a 20.5" tire on it which should raise it just a little bit.
I have not purchased anything for this build yet.everything was laying around that I had or reused. I raised the seat 2".still gotta make it look nice. Also made a link for the front of cradle out of a f250 sway bar link that I shortened. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-31-2019, 07:29 AM | #12 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: Ezgo vangaurd 18
I like the idea of leaving the cart stock looking. If you dress that seat lift up you won't even notice it.
|
10-31-2019, 07:51 AM | #13 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,647
|
Re: Ezgo vangaurd 18
One thought. Unless you install high speed gears without a lift kit your tire size is going to be limited. You top speed will be also be limited.
|
10-31-2019, 09:12 PM | #14 |
Getting Wild
Join Date: May 2017
Posts: 87
|
Re: Ezgo vangaurd 18
My plan is a 20.5 size tire. I don't care about speed at all.just want the impressive torque.
|
11-01-2019, 05:37 AM | #15 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,055
|
Re: Ezgo vangaurd 18
|
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
11-01-2019, 09:34 AM | #16 |
Getting Wild
Join Date: May 2017
Posts: 87
|
Re: Ezgo vangaurd 18
One more question. Does anyone think it would be a problem to have the crank turned to 3/4" and run a spacer to get it to 1". The nose of the crank at skinny part of taper is only 3/4" so it would have to be built up by welding it to 1" and then machined to 1". Just afraid welding it will cause it to be warped.
|
11-01-2019, 09:09 PM | #17 |
Getting Wild
Join Date: May 2017
Posts: 87
|
Re: Ezgo vangaurd 18
I found out today that the vanguard use a forged steel crank so any welding is easily done compared to cast iron.
|
11-01-2019, 10:17 PM | #18 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: Ezgo vangaurd 18
How about just buying a 1" crank? Have you looked into the cost on that? I know there are some members here that stockpile some of these parts, you might be able to get a good crank used from them.
Try posting a thread in the parts section asking about a 1" crank for your engine. |
11-01-2019, 10:40 PM | #19 |
Getting Wild
Join Date: May 2017
Posts: 87
|
Re: Ezgo vangaurd 18
Well the local welding and machine shop at the college is supposed to take care of it for me.price is hard to beat being free and all. A new crank is about 350
|
11-04-2019, 06:37 PM | #20 |
Getting Wild
Join Date: May 2017
Posts: 87
|
Re: Ezgo vangaurd 18
Made a pulley for the starter generator to crank the vanguard.generally these are for farm equipment called a w pulley.
I couldnt find center hub that was narrow enough.i ended up using a collar for a 1" hydraulic cylinder that I was able to weld into the pulley and file a 1/4" keyway slot into it. Little work but at $16 hard to beat. |
|
|
Similar Threads | ||||
Thread | Forum | |||
Vangaurd | Golf Carts and Parts | |||
install 23 hp vangaurd in ezgo gas? | Gas EZGO | |||
Convert EZGO to Vangaurd 35 | Big Block Talk! | |||
18-23 hp vangaurd or b&s motor | Golf Carts and Parts | |||
Vangaurd cam help? | Big Block Talk! |