|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-26-2023, 07:44 PM | #31 | |
Gone Wild
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,544
|
Re: Replaced cables now nothing
Quote:
Sent from my SM-S906U using Tapatalk |
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-27-2023, 10:23 AM | #32 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,131
|
Re: Replaced cables now nothing
This showed up.. little high though. https://www.buggiesgonewild.com/showthread.php?t=190022
|
05-27-2023, 04:33 PM | #33 | |
Not Yet Wild
Join Date: Oct 2022
Posts: 21
|
Re: Replaced cables now nothing
Quote:
|
|
06-03-2023, 08:56 AM | #34 |
Not Yet Wild
Join Date: Oct 2022
Posts: 21
|
Re: Replaced cables now nothing
Thanks again for all the help troubleshooting this. I did end up buying the tsx 3.0 600amp Navitas along with an HD solenoid. Got it installed yesterday after work and much to my disappointment, I still do not have a functional cart. I just shot a quick video that i'm going to post up on youtube today i hope. I have reverse but when i switch to forward and hit the pedal partially, nothing happens. If I fully depress the pedal, I get a slight reverse of the wheels (off the ground) and it's like the controller loses power briefly because I lose connectivity in the app and have to cycle the key on and off the reconnect. I'm wondering if, in the process of upgrading the armature wires, I've broken something down in the motor because both studs moved ever so slightly, maybe an 8th of an inch. Motor is a Advanced DC Motors DE2-4007
Maybe I should start a new thread. |
06-03-2023, 11:14 AM | #35 |
Not Yet Wild
Join Date: Oct 2022
Posts: 21
|
Re: Replaced cables now nothing
Here's a link to a video I just uploaded:
https://www.youtube.com/watch?v=amPVkM5cwd8 I checked continuity on a few things. The FNR switch checked out ok, continuity on middle and outside with the switch one way and no continuity if I throw the switch the other way unless I move to the other outside blade. On the motor, I have continuity between A1 and A2, and F1 and F2 but not between A's or F's. Also, no continuity between any of them and the case of the motor. These test were with all wires disconnected from the controller. |
06-05-2023, 07:48 PM | #36 | |
Gone Wild
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,544
|
Re: Replaced cables now nothing
Quote:
The fault you are getting in forward is low voltage. You need to figure out where you're losing voltage at between the controller and battery pack. Also check the voltage at the battery pack when you try to go forward. A battery could be dropping under the load. Nothing else, now that you have the Navitas installed, give them a call. Their customer service is pretty good. Sent from my SM-S906U using Tapatalk |
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Replaced cables to 2 gauge and cart doesn’t work. | Electric EZGO | |||
G2 replaced F&R cables,input shaft,and driven clutch with no F&R | Gas Yamaha | |||
1 awg cables. What needs replaced? | Electric Club Car | |||
Replaced brake cables Squeak now when pushed | Electric Club Car | |||
Replaced OBC, Charger is good, good cables, Specific gravity is off the charts, but.. | Electric Club Car |