Mikuni throttle cable setup

Bosstin87 · 06-09-2021, 04:42 PM

38mm mikuni knock off. Full swing on the ezgo gas pedal only opens the slide to barely raise above idle. Are there any type of lever setups that will help or any input to get full throttle?

raydhd · 06-09-2021, 05:17 PM

I am a big fan of the speedway motors bell crank. It can be seen on pages 5 and 6 of my 440 cc sled build. There it is pulling a Mikuni VM 34. I will also use this set up on my VC 460 Omega when I get around installing it.

Bosstin87 · 06-09-2021, 05:30 PM

awesome! ill check it out

slonomo · 06-09-2021, 09:04 PM

I made my own bellcrank on two different occasions, worked flawlessly. Here is a video of the bellcrank used on a 23hp vanguard with a Mikuni VM34. It's just some aluminum I had on hand, mounted it to some existing bolts, used small machine screws with washers and nylon lock nuts. The cables are held in with brass cable stops from the auto parts store. I made multiple mounting holes to get it tuned just right. It was smooth and got full travel.

https://www.youtube.com/watch?v=lZyeDKMY40Y

06-09-2021, 04:42 PM	#1
Bosstin87 Not Yet Wild Join Date: Apr 2020 Posts: 71	Mikuni throttle cable setup 38mm mikuni knock off. Full swing on the ezgo gas pedal only opens the slide to barely raise above idle. Are there any type of lever setups that will help or any input to get full throttle?
Bosstin87 Not Yet Wild Join Date: Apr 2020 Posts: 71

06-09-2021, 05:17 PM	#2
raydhd VC 460 CLONE GONE WILD Join Date: Oct 2014 Location: Ray BY The Bay NJ Posts: 10,644	Re: Mikuni throttle cable setup I am a big fan of the speedway motors bell crank. It can be seen on pages 5 and 6 of my 440 cc sled build. There it is pulling a Mikuni VM 34. I will also use this set up on my VC 460 Omega when I get around installing it.

06-09-2021, 05:30 PM	#3
Bosstin87 Not Yet Wild Join Date: Apr 2020 Posts: 71	Re: Mikuni throttle cable setup awesome! ill check it out
Bosstin87 Not Yet Wild Join Date: Apr 2020 Posts: 71

06-09-2021, 09:04 PM	#4
slonomo Searching for The Way Join Date: Oct 2009 Location: Medina, Ohio (NEOHIO) Posts: 11,441	Re: Mikuni throttle cable setup I made my own bellcrank on two different occasions, worked flawlessly. Here is a video of the bellcrank used on a 23hp vanguard with a Mikuni VM34. It's just some aluminum I had on hand, mounted it to some existing bolts, used small machine screws with washers and nylon lock nuts. The cables are held in with brass cable stops from the auto parts store. I made multiple mounting holes to get it tuned just right. It was smooth and got full travel. https://www.youtube.com/watch?v=lZyeDKMY40Y

Similar Threads
Thread	Forum
Yamaha G14/Predator 420 throttle cable setup???	Gas Yamaha
Throttle Setup	Big Block Talk!
EZ-Go Elec. to Gas throttle setup	Big Block Talk!
Throttle cable setup - Lifan	Clone Engine Swaps
gx 390 throttle linkage / cable setup	Clone Engine Swaps

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum