lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric golf carts > Icon


Post New Thread  Reply
 
Thread Tools Display Modes
Old 04-14-2021, 09:28 PM   #11
mwar410
Gone Wild
Yamaha
 
Join Date: Dec 2012
Location: Maine
Posts: 184
Default Re: Lo Speed Switch

Yes the 3 wires with the tape on them. The red black goes to the run/tow switch, and red comes from #1 on the controller, per wire diagram.
mwar410 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 04-15-2021, 10:18 AM   #12
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

Quote:
Originally Posted by mwar410 View Post
Yes the 3 wires with the tape on them. The red black goes to the run/tow switch, and red comes from #1 on the controller, per wire diagram.
The run/tow red/black is +48V to the key switch, which provides +48V to the controller when key is turned on and the run/tow is in run.
mbrown55 is offline   Reply With Quote
Old 04-16-2021, 11:35 AM   #13
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

Here is the picture of the unused 4 pin molex and also the unused 3 singles shown in the schematic.( above the key switch on the wiring schematic)
Attached Images
File Type: jpg E210DD84-A7DD-4E46-820A-470AB0A47626.jpg (127.4 KB, 0 views)
File Type: jpg B999B852-D603-4FC3-8742-9352355F2FF9.jpg (102.8 KB, 0 views)
mbrown55 is offline   Reply With Quote
Old 04-16-2021, 01:29 PM   #14
ATrain
Gone Wild
 
Join Date: Oct 2012
Location: SoCal
Posts: 671
Default Re: Lo Speed Switch

Quote:
Originally Posted by mbrown55 View Post
Here is the picture of the unused 4 pin molex and also the unused 3 singles shown in the schematic.( above the key switch on the wiring schematic)
Are you sure that's not this thing in the upper right? I've noticed that thing too and never knew what it was for.



I've not trusted the accuracy of the diagram. Almost as if it's old/outdated, but maybe not?

I think in the monitoring software, there might be a way to check the status of that switch. Next time I play with the cart I might screw around with that.

I HAVE found another wire that I have no clue about. Under the passenger side front, behind the tube frame support down low by the tire, there's a 2-pin Molex that does something?
ATrain is offline   Reply With Quote
Old 04-16-2021, 01:46 PM   #15
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

That’s the run/tow/EMB switch relay you highlighted. The electric brake draws too much current and is on a relay.

The two pin molex is also shown on the schematic, its the labeled “reverse alarm” on the schematic. Not sure why this was added, they elected to go with the 12V reverse alarm on the extreme left of the schematic which just sends power to the annoying horn in the battery compartment. I think the two pin molex was destined for a reverse indicator light or perhaps to send power to a backup camera.
mbrown55 is offline   Reply With Quote
Old 04-17-2021, 07:12 AM   #16
mwar410
Gone Wild
Yamaha
 
Join Date: Dec 2012
Location: Maine
Posts: 184
Default Re: Lo Speed Switch

So is this just a generic wiring harness for Toyota controllers? Sure seems like some of these connectors and “future” switches would be more suited on a forklift.
mwar410 is offline   Reply With Quote
Old 04-17-2021, 07:45 AM   #17
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

I think it was designed for several brands of generic golf carts. There are several brands based on this basic setup.
mbrown55 is offline   Reply With Quote
Old 04-17-2021, 12:58 PM   #18
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

The black wire is ground on the connector. The blue wire has +5V logic on it when the key is on and must be the #2 pin on the controller. Install a rocker or key switch between the blue and black wires on the 5 pin molex connector (center in is unused) and that should be the high/lo speed switch.
mbrown55 is offline   Reply With Quote
Old 04-17-2021, 01:14 PM   #19
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

Update to last post, looks like that was in error. Running the monitor software grounding the blue wire toggles the brake pedal indicator to the controller. Still searching for the elusive pin #2.
mbrown55 is offline   Reply With Quote
Old 04-17-2021, 01:23 PM   #20
mbrown55
Getting Wild
 
Join Date: Apr 2011
Posts: 93
Default Re: Lo Speed Switch

It has been confirmed, the 5 pin unused molex is for vehicles without electromechanical brake and is shown at the bottom right of the wiring schematic. It tells the controller that a manual brake is set. Back to the drawing board.
mbrown55 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric golf carts > Icon


Thread Tools
Display Modes


Similar Threads
Thread Forum
Speed Switch / Pot Switch on BBB Electric EZGO
Need a new speed switch Electric golf carts
speed switch?!?!?! Columbia ParCar
speed switch Columbia ParCar


All times are GMT -5. The time now is 09:28 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.