|
Big Block Talk! Everything about swapping a big block engine into your cart! |
|
Thread Tools | Display Modes |
05-31-2021, 11:13 AM | #11 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: Rev kit installation
I usually use an off the shelf key switch from local parts store, just make sure it's the Briggs and Stratton type.
There's not much to the wiring. Let me see if I have a diagram of some sort. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-31-2021, 11:51 AM | #12 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: Rev kit installation
I used to have some photos but can't locate them. Here are the factory wiring diagrams for 5 pole and 6 pole type switches.
|
05-31-2021, 02:20 PM | #13 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Rev kit installation
Thanks, I have on hand know is a 6 pole switch and wires, red,black,yellow,white,brown,orange
|
05-31-2021, 02:23 PM | #14 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Rev kit installation
Pic of harness
|
05-31-2021, 02:31 PM | #15 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Rev kit installation
Idk why the images are coming out sideways?
But I have the black wire (ground) to the side terminal, orange to one side of the solenoid post, yellow to the solenoid connector on the side of solenoid, red exposed to be going to the regulator but the terminals are different so I’ll have to solder them together, white wire is for fuel solenoid (not using) and brown ????? Unknown what that’s for |
05-31-2021, 04:26 PM | #16 |
Gone Wild
Join Date: Jun 2011
Location: Kingston Springs Tn.
Posts: 874
|
Re: Rev kit installation
Go to CPP and get isky springs reasonable and proven shims are not that great
|
05-31-2021, 06:58 PM | #17 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Rev kit installation
Those are installed, working on the key switch harness I believe I got every wire correct but I have a brown wire not sure if that is used or not
|
06-02-2021, 05:58 AM | #18 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: Rev kit installation
If you are using the Predator harness I can't be of any help. Never used that. I always run my own new wiring. You'll have to get your multimeter out and do some poking to see what's what. However, the switch tells the story of what each wire will do.
|
06-02-2021, 08:27 PM | #19 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Rev kit installation
Thanks, I got the harness built looks great. My next question is the stock motor plate on my club car is that good to use ? And do u guys use some kind of shock absorber between the plate and motor ?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Installation help | Lithium Club Car | |||
G14 Gas Governor Installation | Gas Yamaha | |||
Canvas Top Installation | Gas Club Car | |||
MP3 amp installation | Electric EZGO | |||
pot box installation | Electric Club Car |