Buggies Gone Wild Golf Cart Forum
Page 1 of 2 1 2 >
Show 40 post(s) from this thread on one page

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Gas Club Car (https://www.buggiesgonewild.com/forumdisplay.php?f=14)
-   -   New floor mat (https://www.buggiesgonewild.com/showthread.php?t=114482)

hondarider203 01-30-2016 11:00 PM
New floor mat
 
Can anyone tell me how to remove the pedals to put a new floor mat one I can't see anywhere how to get them off and I don't want to cut the new mat

Dave in VA 01-31-2016 07:32 AM
Re: New floor mat
 
You'd really be better off just cutting the mat...

lockman1 01-31-2016 08:07 AM
Re: New floor mat
 
1 Attachment(s)
Here's a manual for a 1995-early 96 DS, (it's the earliest manual I have, and it may, or may not be the same as your 88!)
Page 5-8 tells you how to remove the mat, section 6 (mid section) tells how to disassemble the pedal group.

I just read through it... and I'm going to have to agree with Dave! (it looks like a PIA!)
and not knowing how corroded your mounting hardware and misc. parts are... you'll probably run into problems!

.02

miker 01-31-2016 08:36 AM
Re: New floor mat
 
I would cut it then used a carpet tape to keep it together

hondarider203 01-31-2016 09:16 AM
Re: New floor mat
 
OK thanks for the input I cut the old one to get it off to make sure everything was still solid under there and was thing about getting a new diamond plate rubber one but didn't want have to cut it

CCFanatic 01-31-2016 09:18 AM
Re: New floor mat
 
Quote:
Originally Posted by hondarider203 (Post 1237893)
OK thanks for the input I cut the old one to get it off to make sure everything was still solid under there and was thing about getting a new diamond plate rubber one but didn't want have to cut it
Don't cut the new one yet. There is a procedure for putting the new one on with out cutting it. Let me see if I can find it

CCFanatic 01-31-2016 09:20 AM
Re: New floor mat
 
Quote:
Originally Posted by TahoeDawgZ71 (Post 1019179)
You don't have to take the pedals out and you don't have to cut anything. Turn the mat upside down on the floor. Spray the heck out of WD-40 all over the back of the mat. Slowly work it over the brake pedal and slide it all the way down. After it's on the brake, twist the entire mat about 45 degrees counter clockwise and wrap it around the accel pedal. Use a large screwdriver to help wrap it. A small one will tear the mat. Once you've wrapped it around the accel pedal, slowly slide it down until it's underneath it. Rotate mat 45 degrees clockwise and sit it down. You're done. I guess I need to video this and post it. It may be a while before I can get a chance though. DS cars are a rarity these days.
:thumbup:

lockman1 01-31-2016 09:32 AM
Re: New floor mat
 
Leave it to David to figure out a way! :thumbup:

hondarider203 01-31-2016 09:41 AM
Re: New floor mat
 
A-ha awesome I knew there had to be a way to do it, thanks a million

roy63 01-31-2016 02:05 PM
Re: New floor mat
 
was wondering about this also, cant wait to see how to do this, mine is cracked on the drivers side where it bends and goes to the top of the bulkhead or fire wall in the foot well area


All times are GMT -5. The time now is 11:16 AM.
Page 1 of 2 1 2 >
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.