Buggies Gone Wild Golf Cart Forum - First time Alltrax install..

Page 1 of 4

Last »

Show 40 post(s) from this thread on one page

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)

- Electric Club Car (https://www.buggiesgonewild.com/forumdisplay.php?f=13)

- - First time Alltrax install.. (https://www.buggiesgonewild.com/showthread.php?t=147496)

twilliams81

10-31-2018 03:42 PM

First time Alltrax install..

Please forgive my ignorance but which is the proper way to attach cables to the controller? The first way seems to have spring to it and not a solid connection.
https://uploads.tapatalk-cdn.com/201...09d03935c9.jpg
https://uploads.tapatalk-cdn.com/201...6fdc200a0b.jpg

Sent from my iPhone using Tapatalk

Sergio

10-31-2018 03:55 PM

Re: First time Alltrax install..

The lug goes on top of the metal tab.

Keep pressure downward when You are tightening so the nut stays captive in the recess provided and does not twist.

The springing action you are feeling is fine since the electrical connection is between the lug and the thin tab itself.

twilliams81

10-31-2018 03:56 PM

Re: First time Alltrax install..

Thanks again Sergio!

Sent from my iPhone using Tapatalk

Hit it like a champ

11-01-2018 12:20 AM

Re: First time Alltrax install..

I had a terrible time doing this I hope you make out better than I did. Good luck buddy.

twilliams81

11-01-2018 06:47 AM

Re: First time Alltrax install..

Ohh yeah? What were some of the issues you ran into?

Sent from my iPhone using Tapatalk

twilliams81

11-01-2018 06:49 AM

Re: First time Alltrax install..

Quote:

Originally Posted by Hit it like a champ (Post 1555440)

I had a terrible time doing this I hope you make out better than I did. Good luck buddy.

Yeah?? What were some of the issues you ran into?

Sent from my iPhone using Tapatalk

Hit it like a champ

11-01-2018 09:23 AM

Re: First time Alltrax install..

The diodes make sure they are correct with the stripe on the correct side. And I had the motor wires reversed.

twilliams81

11-01-2018 09:50 AM

First time Alltrax install..

I’m doing the 500 XCT with the 400 amp solenoid..doesn’t that one only have the one diode?

Sent from my iPhone using Tapatalk

scottyb

11-01-2018 10:05 AM

Re: First time Alltrax install..

Quote:

Originally Posted by twilliams81 (Post 1555558)

I’m doing the 500 XCT with the 400 amp solenoid..doesn’t that one only have the one diode?

Sent from my iPhone using Tapatalk

Look at the install diagram in your owners manual. It shows 2 diodes that need to be installed. One is small and short and fits between the 2 small posts on the solenoid (as shown in the manual). Polarity is critical. The stripe on the diode indicates the + end. When installed this end needs to towards the + wire also shown in the install diagram.
The second diode is larger... it comes with every Ezgo and CC XCT controller with instructions to put it on the large terminals. In this application the striped end (+) goes toward the post with the main positive battery cable attached.
I hope this helps

twilliams81

11-01-2018 10:10 AM

Re: First time Alltrax install..

It does and thanks again Scotty. I hate to keep bothering you with every little question. Anyone reading this and considering doing this upgrade I highly recommend getting your setup from ScottyB @ carts unlimited! First rate service all the way!

Sent from my iPhone using Tapatalk

All times are GMT -5. The time now is 05:54 AM.

Page 1 of 4

Last »

Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.