Kubota D662 install in Yamaha Cart
 

New here to the forum. I am just starting a project to install a Kubota D662 in a Yamaha gas cart. I have been looking for the best way to mount the clutch to the fly wheel and came across a bearing supported stub shaft made by Hayes for the D662.

If anyone has ever installed one and has any tips on the clutch to use I would appreciate the help. I'm a bit stumped as to how the belt drive will work on an engine that has to be running, unless there is a system that has a higher RMP engagement.

Thanks

Re: Kubota D662 install in Yamaha Cart
 

Now that's my kind of conversion !!! DIESEL FUEL ONLY

Re: Kubota D662 install in Yamaha Cart
 

http://www.buggiesgonewild.com/big-b...ota-build.html
Here's how I did it.

Re: Kubota D662 install in Yamaha Cart
 

Club car used a kubota D722 in a few models of their carts/utility vehicles. They make a flywheel adapter to adapt to the taper shaft on our clutches. I don't have the part number handy right now but I'll post it later. I bought 2 adapters from Tahoedawg here on the forum and I also have A straight shaft flywheel adapter for 1 1/8th inch that I bought from kubota that came out of japan. Both just bolt to the Super mini series flywheel...Z482, D602, D662, etc etc all the way up to D902. You will have to play with weights in the clutch to get it to shift out properly....you may be able to get 4000 rpm out of it if you play with the fueling a bit. That engine will either be rated 3200 rpm or 3600 depending on injection timing....either will do 3600 easily.

The flywheel you need that works with these adapters is the one that comes with the plain Jane no option engine....it will have a steel plate bolted to the back of the engine instead of a bell housing. 5 bolts for the flywheel then 5 threaded holes around the flywheel for the adapter.

Re: Kubota D662 install in Yamaha Cart
 

Club car P/N: 102465901 Shaft, CVT Adapter

Heres what it looks like. You do not need a support bearing.
http://www.buggiesgonewild.com/images/cvtadapt.jpg

If you decide to call tahoedawgz71 or pm him keep in mind he will have to order it, it doesn't take long to get it though. Its not a common item so no one stocks it on the shelf.

Re: Kubota D662 install in Yamaha Cart
 

Kubota Super mini series flywheel

http://www.buggiesgonewild.com/cvt/CAM00108.jpg

Club Car's Kubota CVT adapter
http://www.buggiesgonewild.com/cvt/CAM00100.jpg

http://www.buggiesgonewild.com/cvt/CAM00102.jpg

http://www.buggiesgonewild.com/cvt/cvt/CAM00112.jpg
http://www.buggiesgonewild.com/cvt/cvt/CAM00113.jpg


Kubota 1.125 with .250 key straight shaft adapter.
http://www.buggiesgonewild.com/cvt/CAM00105.jpg

Kawasaki mule CVT with Club Car CVT adapter on Flywheel.
http://www.buggiesgonewild.com/cvt/cvt/CAM00118.jpg

http://www.buggiesgonewild.com/cvt/cvt/CAM00119.jpg

Re: Kubota D662 install in Yamaha Cart
 

Where can I find the Kubota 1.125 with .250 key straight shaft adapter?
Part number?

Thanks

Re: Kubota D662 install in Yamaha Cart
 

I'm really interested too in how you got that shaft adapter. Any info would be much appreciated.

Thank you!

Re: Kubota D662 install in Yamaha Cart
 

I am interested myself lol wish I had a phone number to call someone about this issue.

Re: Kubota D662 install in Yamaha Cart
 

check out this guys ebay. i just bought one and it was a perfect fit for my d600.. 1 inch shaft, fits the 5 bolts on the flywheel. not sure how many he has

https://www.ebay.com/itm/27501958677...53.m2749.l2648