Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Gas Harley Davidson (https://www.buggiesgonewild.com/forumdisplay.php?f=81)
-   -   Primary drive sleeve (https://www.buggiesgonewild.com/showthread.php?t=188301)

Myyke 01-03-2023 05:44 PM

Primary drive sleeve
 
Hi folks,
Anyone happen to know the outer diameter for the needle bearing sleeve on the primary drive?

I found the bearing & seals i need, but i need to build a sleeve.

Thanks in advance.

Scooter_Trash 01-05-2023 09:25 PM

Re: Primary drive sleeve
 
Quote:

Originally Posted by Myyke (Post 1924025)
Hi folks,
Anyone happen to know the outer diameter for the needle bearing sleeve on the primary drive?

I found the bearing & seals i need, but i need to build a sleeve.

Thanks in advance.

Got a part number Mike?

Leon willis 01-06-2023 10:28 PM

Re: Primary drive sleeve
 
Inch and a 1/2 been a minute since I had my cart apart so don’t quote me sorry

Myyke 01-08-2023 02:07 PM

Re: Primary drive sleeve
 
Quote:

Originally Posted by Scooter_Trash (Post 1924326)
Got a part number Mike?

No not yet. I’ll have to look in my parts manual. Thanks

Myyke 01-09-2023 12:11 PM

Re: Primary drive sleeve
 
Quote:

Originally Posted by Scooter_Trash (Post 1924326)
Got a part number Mike?

So here is the info i’ve been able to find.

In the 1963-80 gas manual:
Sec 4 pg 4, figure 4b-43. #20a needle bearing, late 64( looking for the sleeve on the outside)

In the 1963-81 gs parts book i have:
Page 9, part 29 in pic,
Part#’s are:
36462-64 needle bearing sleeve assembly (64 to 66)
36462-67 (67 to present)

If i could find just the outside sleeve dimensions or drawing i could build my own.

Scooter_Trash 01-09-2023 04:29 PM

Re: Primary drive sleeve
 
1 Attachment(s)
Quote:

Originally Posted by Myyke (Post 1924747)
So here is the info i’ve been able to find.

In the 1963-80 gas manual:
Sec 4 pg 4, figure 4b-43. #20a needle bearing, late 64( looking for the sleeve on the outside)

In the 1963-81 gs parts book i have:
Page 9, part 29 in pic,
Part#’s are:
36462-64 needle bearing sleeve assembly (64 to 66)
36462-67 (67 to present)

If i could find just the outside sleeve dimensions or drawing i could build my own.

the 36462-64 sleeve is:
.78" L
1.5" OD
1.368 ID (difficult for me to measure, so your bearing OD should dictate)
In case you don't have an old one, I'll note that this sleeve captures the bearing between two oil seals.
Good Luck!

Myyke 01-09-2023 05:01 PM

Re: Primary drive sleeve
 
Quote:

Originally Posted by Scooter_Trash (Post 1924779)
the 36462-64 sleeve is:
.78" L
1.5" OD
1.368 ID (difficult for me to measure, so your bearing OD should dictate)
In case you don't have an old one, I'll note that this sleeve captures the bearing between two oil seals.
Good Luck!

Exactly what i was looking for. Thank you very much.
Looks like the seals are backwards to what i usually see on other things. Wasn’t sure which way they went in.
Thanks again.

Here is what i was able to find for bearings & seals according to the inner race i had.
Seal: National brand pt# 340815
Bearing: BA188Z

Scooter_Trash 01-09-2023 06:21 PM

Re: Primary drive sleeve
 
Quote:

Originally Posted by Myyke (Post 1924782)
Exactly what i was looking for. Thank you very much.
Looks like the seals are backwards to what i usually see on other things. Wasn’t sure which way they went in.
Thanks again.

Here is what i was able to find for bearings & seals according to the inner race i had.
Seal: National brand pt# 340815
Bearing: BA188Z

Thanks for posting the cross refs.
The seal on the opposite side is ALSO inserted opposite, so both seals face in the same direction.

Myyke 01-09-2023 07:28 PM

Re: Primary drive sleeve
 
Quote:

Originally Posted by Scooter_Trash (Post 1924789)
Thanks for posting the cross refs.
The seal on the opposite side is ALSO inserted opposite, so both seals face in the same direction.

I like sharing any updated info i can find, if it help others.

Myyke 01-10-2023 10:42 AM

Re: Primary drive sleeve
 
Update: was measuring up parts last night, i found i have to change sleeve dimensions to a different size.

New outer sleeve size with seals i was able to find:
1.00” wide
1.368” I.D.
1.55” O.D. same diameter as Primary Floating sleeve (one with felt). 340815 seal is 1.5”
1.03” Original primary inner sleeve
Once i build one i’ll post a pic.


All times are GMT -5. The time now is 07:09 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.