Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Body and Paint (https://www.buggiesgonewild.com/forumdisplay.php?f=59)
-   -   prep work for painting plastic bodies (https://www.buggiesgonewild.com/showthread.php?t=22929)

master66 09-08-2009 04:05 PM

prep work for painting plastic bodies
 
I will try to give as much information as I can about doing prep work to plastic and metal bodies for paint. There seems to be quite a few questions about plastic and prep work so here goes, and remember these are just my personal preferences so you may use any product or method you wish.

Plastic bodies:
The very first thing is you can either remove the body parts to be worked or you can leave them on and mask everything, it,s personal preference but removing the parts usually works better. After that you need to scuff the whole body with either burgundy scotchbrite or sandpaper about 240 -400 grit dry paper, make sure you just remove the shine with the scuffing and not sand like crazy.
After scuffing now is the time to wipe it down with some wax and grease remover, wipe it on with one rag and wipe it off with another. Now you can do any bodywork that needs to be done, for filling scratches and gouges a polyester based finishing putty works the best for that, unlike the heavier "Bondo type" filler the finishing putty sand easier and doesn't tend to leave pinholes.I usually sand the putty with 240-320 grit dry paper then wax and grease again, remember wipe on wipe off.
Now is one of the most important parts "Adhesion promoter", this is a product that is sprayed on that softens up the plastic to accept primers and paints, if you do not do this step you risk all material you put on from here on out flaking or peeling off, especially if you are applying graphics later. Even if you are using Krylon Fusion I would still apply adhesion promoter. There are many different brands but I use either PPG or Dupont, make sure you read directions for applications and dry times.
Now you can pick a paint system and prime, if you are going to use automotive paint than I probably would not use bomb can primer, pick a primer that you're finished product material will accept. Prime accordingly, usually 2 to 3 good coats will do, then I usually sand with 240 grit if you are going to apply more primer later or 400-600 grit if this is you're finish sanding, and if you break through the primer in spots I would re prime and then spray a sealer on before applying color.If you have wet and dry sand paper you can wet sand if you like but I usually just use dry paper.
Just remember plenty of scuffing, adhesion promoter and plenty of wax and grease remover steps and you're job should turn out just fine.

Kevin :mrgreen:

SpoiledRotten 09-08-2009 04:54 PM

Re: prep work for painting plastic bodies
 
Very good, Kevin. I didn't see the "tack cloth" step though. Is that really not that necessary?

galloway 09-08-2009 05:01 PM

Re: prep work for painting plastic bodies
 
Thanks Kevin for putting this out here. Glad you put that part about the promoter product I was wondering what I need to find to help out. I know with pvc pipe we use the purple primer to get the plastic nice and warm to weld to the other plastic. Just wondering how the paint worked.

Thanks Again.

essness 09-08-2009 07:16 PM

Re: prep work for painting plastic bodies
 
Can we sticky this??

tonyton 09-08-2009 07:39 PM

Re: prep work for painting plastic bodies
 
It needs to be stickied. He's already gone through this 100 times.:lol: Good job Kevin:thumbup:

master66 09-09-2009 08:06 AM

Re: prep work for painting plastic bodies
 
Quote:

Originally Posted by SpoiledRotten (Post 278620)
Very good, Kevin. I didn't see the "tack cloth" step though. Is that really not that necessary?

The tack cloth is really not needed untill you start spraying the color and clear because you will pretty much be sanding out any debris in the primer out anyway, good question though. If I have time I will try to do one on prepping fiberglass and metal bodies also if you guys think it is needed.

scottyb 09-09-2009 08:14 AM

Re: prep work for painting plastic bodies
 
Great info Kevin ..... thank you!

TheNewGuy 09-09-2009 08:21 AM

Re: prep work for painting plastic bodies
 
Thanks Kevin.

hawkeyedm2003 09-13-2009 07:28 PM

Re: prep work for painting plastic bodies
 
Great write up.

2 questions for a newb...

What is "bomb can primer"?

How is the adhesion promoter applied? (same as paint with a gun?)

SpoiledRotten 09-13-2009 07:47 PM

Re: prep work for painting plastic bodies
 
Bomb can is a professionals name for rattle can spray paints from Walmart and other retailers.

Like instrumentalist call accompaniment tapes and CDs, canned music. They don't like it when you sing to "canned music". They'd rather you use the real thing.


All times are GMT -5. The time now is 03:32 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.