Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Clone Engine Swaps (https://www.buggiesgonewild.com/forumdisplay.php?f=91)
-   -   Belt Resources (https://www.buggiesgonewild.com/showthread.php?t=148188)

superpro56 11-28-2018 01:30 PM

Belt Resources
 
After installing my VC625 in a 96CC, I think I would like to switch to a shorter belt. I have a couple interference issues on the front side, with a lot of room between the engine and transaxle. Hoping for a resource for belts of varying sizes, preferably double-cogged for extreme performance. I know the belt is 1-3/16" wide, but I'm not certain of its circumference.

BBBHC 11-28-2018 02:38 PM

Re: Belt Resources
 
Don't know for sure, but I heard this company can do custom belt sizes, and/or match up appropriate belts.

https://www.powermotorsports.com/we-...r-utv--service

raydhd 11-28-2018 02:57 PM

Re: Belt Resources
 
You can use Dayco.com/parts and look at ATV or snowmobiles and use width and length chart to find your desired size. I found the 1 1/4 belt works fine on the comet 780 clutch. Once you have the dayco part # there are all kinds of places that sell them including E bay where often a deal can be had.For example if your present belt is 44" around the outside and you want to move your engine 2"s forward you need to find a 40" belt. P.S. Don't know length needed for a 625 swap but on my VC 460 powered G 14 I am using the Dayco XTX 2264 which measures 42.83 X 1.25 "'s and is rated for over 100 hp.

Shepard 11-28-2018 05:58 PM

Re: Belt Resources
 
Quote:

Originally Posted by superpro56 (Post 1563305)
After installing my VC625 in a 96CC, I think I would like to switch to a shorter belt. I have a couple interference issues on the front side, with a lot of room between the engine and transaxle. Hoping for a resource for belts of varying sizes, preferably double-cogged for extreme performance. I know the belt is 1-3/16" wide, but I'm not certain of its circumference.

By chance do you have the old belt from the original setup? If so -- cut it and use it for a measuring rule. Put the engine where you want and wrap it around the pulleys and measure accordingly to determine the proper length belt.

AaronW 11-28-2018 06:17 PM

Re: Belt Resources
 
Quote:

Originally Posted by Shepard (Post 1563352)
By chance do you have the old belt from the original setup? If so -- cut it and use it for a measuring rule. Put the engine where you want and wrap it around the pulleys and measure accordingly to determine the proper length belt.

You can also use a piece of string to do this! A belt can always come in handy. Let's keep em around. :)

Shepard 11-29-2018 01:06 AM

Re: Belt Resources
 
Quote:

Originally Posted by AaronW (Post 1563354)
You can also use a piece of string to do this! A belt can always come in handy. Let's keep em around. :)

Junk is junk -- why not make a tool out of it. That's pretty handy.

superpro56 11-29-2018 09:10 AM

Re: Belt Resources
 
I threw my old belt away when I pulled it, I knew I would get a new one with the 625 and the existing belt was past due for replacement. Gonna give the string a shot and see if I can center this engine up a little bit. Hopefully Dayco has something that doesn't cost an arm and a leg.

raydhd 11-29-2018 09:44 AM

Re: Belt Resources
 
I have a Dayco HPX 2248 I used as A test belt.It measures 44.72 X 1.26 "'s. It was 2"'s too long for my set up. If it is what you need PM me and I'll give you a half price deal on it.

9SecBuick 11-29-2018 10:14 PM

Re: Belt Resources
 
Quote:

Originally Posted by superpro56 (Post 1563305)
After installing my VC625 in a 96CC, I think I would like to switch to a shorter belt. I have a couple interference issues on the front side, with a lot of room between the engine and transaxle. Hoping for a resource for belts of varying sizes, preferably double-cogged for extreme performance. I know the belt is 1-3/16" wide, but I'm not certain of its circumference.

The belt in the kit is 42x1.188

raydhd 11-29-2018 10:37 PM

Re: Belt Resources
 
I did the Dayco search and found. XTX2244=39.5 X 1.24, XTX2268=39.719 X 1.261 ,XTX2281=37.563 X 1.21, and XTX2282=37.625 X 1.26.


All times are GMT -5. The time now is 06:55 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.